{ "sheet": "E2.3", "notes": [ "1. FOR HOME RUNS (FROM UNITS) 100 FT OR MORE, THE ELECTRICAL CONTRACTOR HAS TO CHECK THE VOLTAGE DROP AND SELECT THE SUITABLE CABLES SIZE TO COMPLY WITH THE MAXIMUM ALLOWED VOLTAGE DROP FOR THE BRANCH CIRCUIT (3%).", "2. THE CONTRACTOR SHALL VERIFY WITH THE OWNER FOR THE APPROVED BRANDS/ MODELS OF THE LOW VOLTAGE SYSTEM DEVICES (CAMERA, CARD READER, WIRELESS ACCESS POINT, ETC.) AND PROVIDE ALL NECESSARY ACCESSORIES TO COMPLETE THE WIRING, POWER SUPPLY FOR THE DEVICES AS PER THE MANUFACTURER SPECIFICATIONS/ INSTALLATION GUIDELINES.", "3. LIGHTING FOR ALL EXTERIOR APPLICATIONS SHALL HAVE AUTOMATIC CONTROLS CAPABLE OF TURNING OFF EXTERIOR LIGHT WHEN SUFFICIENT DAYLIGHT IS AVAILABLE OR WHEN THE LIGHT IS NOT REQUIRED DURING NIGHTTIME HOURS. LIGHTING NOT DESIGNATED FOR DUSK TO DAWN OPERATION SHALL BE CONTROLLED BY AN ASTRONOMICAL TIME SWITCH. LIGHTING DESIGNATED FOR DUSK TO DAWN SHALL BE CONTROLLED BY AN ASTRONOMICAL TIME SWITCH OR PHOTOSENSOR. ASTRONOMICAL TIME SWITCHES SHALL BE CAPABLE OF RETAINING PROGRAMMING AND THE TIME SETTING DURING LOSS OF POWER FOR A PERIOD OF AT LEAST 10 HOURS.", "4. THE OCCUPANCY SENSOR SWITCHES SHALL AUTOMATICALLY TURN LIGHTING ON INSTANTANEOUSLY WHEN THE ROOM/SPACE IS OCCUPIED AND AUTOMATICALLY TURN LIGHTING OFF WITHIN 30 MINUTES OF ALL OCCUPANTS LEAVING THAT ROOM/SPACE.", "5. THE EMERGENCY AND EXIT LIGHTS THAT CONNECT TO LOCAL AREA NORMAL LIGHTING CIRCUITS WILL BE CONNECTED AHEAD OF ANY LOCAL SWITCHES COMPLY WITH NEC 700.12(F).", "6. EMERGENCY LIGHTING FACILITIES SHALL BE ARRANGE TO PROVIDE INITIAL ILLUMINATION THAT IS AT LEAST 10 FOOT-CANDLES OF EMERGENCY ILLUMINATION SHALL BE PROVIDED ON THE STAIRS AND 1 FOOT-CANDLE ON THE OTHER WALKING SURFACES PER NFPA 101 (SECTION 7.8.1.3 AND 7.9).", "7. LOW-LEVEL EXIT SIGNS SHALL BE PROVIDED IN ALL AREAS SERVING GUESTROOMS IN GROUP R-1 OCCUPANCIES BY SECTION 1013.1 AND SHALL COMPLY WITH SECTION 1013.5. THE BOTTOM OF THE SIGN SHALL BE NOT LESS THAN 10 INCHES (254MM) NOR MORE THAN 18 INCHES (455MM) ABOVE THE FLOOR LEVEL. THE SIGN SHALL BE FLUSH MOUNTED TO THE DOOR OR WALL. WHERE MOUNTED ON WALL, THE EDGE OF THE SIGN SHALL BE WITHIN 4 INCHES (102MM) OF THE DOOR FRAME ON THE LATCH SIDE.", "8. VERIFY MOUNTING HEIGHT FOR ALL WALL MOUNTED FIXTURE TYPES WITH OWNER/ARCH. PRIOR INSTALLATION.", "9. SEE TYPICAL GUESTROOM PLAN FOR DETAILED ROOM LAYOUT ON SHEETS E4.0, E4.1.", "10. LUMINAIRES INSTALLED IN WET OR DAMP LOCATIONS SHALL BE INSTALLED SUCH THAT WATER CANNOT ENTER OR ACCUMULATE IN WIRING COMPARTMENTS, LAMP HOLDERS, OR OTHER ELECTRICAL PARTS. ALL LUMINAIRES SHALL BE SELECTED SUITABLE FOR WET LOCATIONS OR DAMP LOCATION.", "11. CONTRACTOR SHALL VERIFY AND FURNISH EXIT SIGNS TO COMPLY WITH SECTION 1013 IBC REQUIREMENT.", "12. THE ELECTRICAL CONTRACTOR SHALL COORDINATE WITH THE SPRINKLER CONTRACTOR FOR THE PLACEMENTS OF THE LIGHT FIXTURES AND SPRINKLER HEADS TO COMPLY WITH THE NFPA 13 REQUIREMENTS.", "13. SUFFICIENT EMERGENCY LIGHTING LEVELS WILL BE DETERMINED DURING THE ONSITE INSPECTION. ADDITIONAL EMERGENCY LIGHTING MAY BE REQUIRED BY FIELD INSPECTOR IF DEEMED INSUFFICIENT.", "1. CONNECT ALL TYPE \"S02\", \"X1\" & \"X2\" LIGHTS AT STAIRCASE TO L1.B-33 USING 2#10, 1/2\"C. CONTRACTOR WILL PROVIDE A LOCK-ON FEATURE FOR THIS CIRCUIT AS REQUIRED BY NEC 700.12(I)(2)(3).", "2. OCCUPANT SENSOR CONTROLS IN CORRIDORS SHALL UNIFORMLY REDUCE LIGHTING POWER TO AN UNOCCUPIED SETPOINT NOT MORE THAN 50 PERCENT OF FULL POWER WITHIN 20 MINUTES AFTER ALL OCCUPANTS HAVE LEFT THE SPACE (C405.2.1.4). VERIFY THE DETECTION RANGE OF THE OCCUPANCY SENSORS, AND THE LOCATION AND QUANTITIES OF THE OCCUPANCY SENSORS WITH THE SUPPLIER /MANUFACTURER SPECIFICATIONS & GUIDELINES PRIOR TO INSTALLATION.", "3. FAN WILL RUN CONTINUOUSLY AS THE NOTE ON EXHAUST FAN SCHEDULES (M1.1).", "{\"EF-1\": 1, \"EF-1.1\": 1, \"EM\": 11, \"HOME-RUN\": 1, \"OS\": 7, \"PA-204\": 25, \"R11\": 21, \"S01\": 1, \"S02\": 4, \"X1\": 3, \"X2\": 2, \"X3\": 5}", "17 corridor + 4 elevator lobby = 21", "2 Stair 2 + 2 Stair 1 = 4", "6 corridor + 2 Stair 2 + 2 Stair 1 + 1 Storage = 11", "64 source curves; 395.616 raw LF; 395.5 LF aggregate rounded to nearest 0.5", "24 room labels retained; no furniture/typical-room symbol counted as an E2.3 installed fixture", "10800/2592 = 7200/1728 = 4.1666667 raster pixels/PDF point; 9 PDF points/ft = 37.5 raster pixels/ft" ], "assemblies": [ [ "Common-area lighting network", "Every PA-204, R11, EM, exit sign, sensor, stair/storage fixture, fan load, home run and visible connection curve is individually retained." ], [ "Guestroom scope", "Twenty-four room labels retained as evidence; no interior fixture or route is inferred from the architectural background." ], [ "Emergency stair circuit", "Keyed Note 1 calls for S02/X1/X2 on L1.B-33 using 2#10 in 1/2-inch conduit with lock-on feature; plotted X3 remains a coordination issue." ] ], "registers": { "fullAudit": { "schemaVersion": "1.0", "sheet": { "number": "E2.3", "title": "LIGHTING FOURTH FLOOR PLAN", "engineeringPDFPage": 40, "pdfIndex": 39, "project": "210729", "date": "NOV 22 2024", "drawnBy": "PL", "checkedBy": "DV", "revisionEntries": [] }, "source": { "pdf": "/workspace/sites/ssx-cover-release/source-plans/engineering.pdf", "raster": "/workspace/sites/ssx-cover-release/tmp/pdfs/next5-e12-e23/source-40.png", "ocrText": "/workspace/sites/ssx-cover-release/tmp/pdfs/next5-e12-e23/source-40.txt", "rasterPixels": [ 10800, 7200 ], "pdfPoints": [ 2592, 1728 ], "normalization": "normalized x=sourceRasterX*1920/10800=PDFx/1.35; y=sourceRasterY*1280/7200=PDFy/1.35", "reviewMethod": "Full-resolution raster reviewed left-to-right/top-to-bottom; repeated plotted symbols counted once each; vector PDF geometry used to recover exact drawn circuit curves and stable symbol centers. OCR text was not accepted where absent or illegible.", "limitations": [ "source-40.txt contains title/room text but omits most plotted SHX-style tags and note bodies", "Marker coordinates for EM, S01, S02 and OS are visual centers and are less exact than vector-derived PA-204/R11/exit centers.", "No quantity was inferred inside guestrooms; E4.0/E4.1 references remain separate." ] }, "coordinateSpace": { "width": 1920, "height": 1280, "origin": "top-left", "sourceToNormalizedFactor": 0.1777777778 }, "regions": [ { "id": "plan", "label": "Plan 1 / Lighting Fourth Floor Plan", "bbox": [ 235, 182, 1515, 716 ] }, { "id": "generalNotes", "label": "General Notes", "bbox": [ 330, 740, 1032, 1155 ] }, { "id": "keyedNotes", "label": "Keyed Notes", "bbox": [ 1065, 740, 1565, 940 ] }, { "id": "titleBlock", "label": "Title block", "bbox": [ 1595, 0, 1920, 1280 ] } ], "scale": { "printed": "1/8 inch = 1 foot", "pdfPointsPerFoot": 9.0, "sourceRasterPixelsPerFoot": 37.5, "normalizedUnitsPerFoot": 6.6666667, "verification": "PDF page is 2592x1728 points and raster is 10800x7200 pixels (exact 300 dpi); 1/8-inch printed scale therefore equals 9 PDF points or 37.5 source pixels per foot. No independent dimension chain is printed in the lighting plan field.", "status": "PRINTED SCALE VERIFIED TO PDF/RASTER RESOLUTION; NOT INDEPENDENTLY CHECKED AGAINST A DIMENSION STRING" }, "counts": [ { "tag": "PA-204", "description": "corridor wall sconce", "quantity": 25, "unit": "EA", "confidence": "certified" }, { "tag": "R11", "description": "recessed downlight", "quantity": 21, "unit": "EA", "breakdown": { "corridor": 17, "elevatorLobby": 4 }, "confidence": "certified" }, { "tag": "S01", "description": "storage utility fixture", "quantity": 1, "unit": "EA", "confidence": "certified" }, { "tag": "S02", "description": "stair strip fixture", "quantity": 4, "unit": "EA", "breakdown": { "Stair 2": 2, "Stair 1": 2 }, "confidence": "certified" }, { "tag": "EM", "description": "emergency lighting unit", "quantity": 11, "unit": "EA", "breakdown": { "corridor": 6, "Stair 2": 2, "Stair 1": 2, "Storage 423": 1 }, "confidence": "certified" }, { "tag": "X1", "description": "single-face exit sign", "quantity": 3, "unit": "EA", "confidence": "certified" }, { "tag": "X2", "description": "two-face exit sign", "quantity": 2, "unit": "EA", "confidence": "certified" }, { "tag": "X3", "description": "wall exit sign", "quantity": 5, "unit": "EA", "confidence": "certified" }, { "tag": "OS", "description": "occupancy sensor/control symbol", "quantity": 7, "unit": "EA", "breakdown": { "corridor": 6, "elevatorLobby": 1 }, "confidence": "certified" }, { "tag": "EF-1", "description": "exhaust fan motor/load point", "quantity": 1, "unit": "EA", "confidence": "certified" }, { "tag": "EF-1.1", "description": "exhaust fan motor/load point", "quantity": 1, "unit": "EA", "confidence": "certified" }, { "tag": "HOME-RUN", "description": "L1.B-25,27 home-run/circuit callout", "quantity": 1, "unit": "OCCURRENCE", "confidence": "certified" } ], "markers": [ { "id": "E23-EF1-01", "tag": "EF-1", "category": "equipment_load", "center": [ 1340.74, 251.85 ], "sourcePDFPoint": [ 1810, 340 ], "status": "counted_plotted_occurrence", "note": "Storage exhaust-fan motor/load point." }, { "id": "E23-S02-03", "tag": "S02", "category": "luminaire", "center": [ 1448.15, 255.56 ], "sourcePDFPoint": [ 1955.0, 345.0 ], "status": "counted_plotted_occurrence", "note": "Two fixtures in each stair; keynote 1." }, { "id": "E23-EM-10", "tag": "EM", "category": "emergency_lighting", "center": [ 1472.89, 279.11 ], "sourcePDFPoint": [ 1988.4, 376.8 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-R11-18", "tag": "R11", "category": "luminaire", "center": [ 1301.02, 287.56 ], "sourcePDFPoint": [ 1756.38, 388.21 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-19", "tag": "R11", "category": "luminaire", "center": [ 1362.84, 287.56 ], "sourcePDFPoint": [ 1839.84, 388.21 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-OS-07", "tag": "OS", "category": "lighting_control", "center": [ 1331.85, 310.37 ], "sourcePDFPoint": [ 1798, 419 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-S01-01", "tag": "S01", "category": "luminaire", "center": [ 1324.44, 324.44 ], "sourcePDFPoint": [ 1788.0, 438.0 ], "status": "counted_plotted_occurrence", "note": "Single storage-room utility fixture; plotted tag legible." }, { "id": "E23-EM-09", "tag": "EM", "category": "emergency_lighting", "center": [ 1302.22, 325.33 ], "sourcePDFPoint": [ 1758, 439.2 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-R11-20", "tag": "R11", "category": "luminaire", "center": [ 1301.02, 339.32 ], "sourcePDFPoint": [ 1756.38, 458.08 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-21", "tag": "R11", "category": "luminaire", "center": [ 1362.84, 339.32 ], "sourcePDFPoint": [ 1839.84, 458.08 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-EM-11", "tag": "EM", "category": "emergency_lighting", "center": [ 1420.44, 344.89 ], "sourcePDFPoint": [ 1917.6, 465.6 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-S02-04", "tag": "S02", "category": "luminaire", "center": [ 1448.15, 365.19 ], "sourcePDFPoint": [ 1955.0, 493.0 ], "status": "counted_plotted_occurrence", "note": "Two fixtures in each stair; keynote 1." }, { "id": "E23-X3-03", "tag": "X3", "category": "exit_sign", "center": [ 1352.87, 371.89 ], "sourcePDFPoint": [ 1826.37, 502.05 ], "status": "counted_plotted_occurrence", "note": "Wall exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-X1-02", "tag": "X1", "category": "exit_sign", "center": [ 1332.33, 379.53 ], "sourcePDFPoint": [ 1798.65, 512.37 ], "status": "counted_plotted_occurrence", "note": "Single-face exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-X3-05", "tag": "X3", "category": "exit_sign", "center": [ 1462.02, 380.02 ], "sourcePDFPoint": [ 1973.73, 513.03 ], "status": "counted_plotted_occurrence", "note": "Wall exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-PA204-25", "tag": "PA-204", "category": "luminaire", "center": [ 1479.13, 392.07 ], "sourcePDFPoint": [ 1996.83, 529.29 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-EF11-01", "tag": "EF-1.1", "category": "equipment_load", "center": [ 1335.56, 400.0 ], "sourcePDFPoint": [ 1803, 540 ], "status": "counted_plotted_occurrence", "note": "Exhaust-fan motor/load point; keyed note 3." }, { "id": "E23-EM-02", "tag": "EM", "category": "emergency_lighting", "center": [ 564.44, 408.15 ], "sourcePDFPoint": [ 762, 551 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-EM-04", "tag": "EM", "category": "emergency_lighting", "center": [ 964.44, 408.15 ], "sourcePDFPoint": [ 1302, 551 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-EM-06", "tag": "EM", "category": "emergency_lighting", "center": [ 1364.44, 408.15 ], "sourcePDFPoint": [ 1842, 551 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-PA204-01", "tag": "PA-204", "category": "luminaire", "center": [ 316.33, 409.27 ], "sourcePDFPoint": [ 427.05, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-02", "tag": "PA-204", "category": "luminaire", "center": [ 404.2, 409.27 ], "sourcePDFPoint": [ 545.67, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-03", "tag": "PA-204", "category": "luminaire", "center": [ 485.36, 409.27 ], "sourcePDFPoint": [ 655.23, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-04", "tag": "PA-204", "category": "luminaire", "center": [ 587.0, 409.27 ], "sourcePDFPoint": [ 792.45, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-05", "tag": "PA-204", "category": "luminaire", "center": [ 741.98, 409.27 ], "sourcePDFPoint": [ 1001.67, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-06", "tag": "PA-204", "category": "luminaire", "center": [ 823.13, 409.27 ], "sourcePDFPoint": [ 1111.23, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-07", "tag": "PA-204", "category": "luminaire", "center": [ 910.87, 409.27 ], "sourcePDFPoint": [ 1229.67, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-08", "tag": "PA-204", "category": "luminaire", "center": [ 991.98, 409.27 ], "sourcePDFPoint": [ 1339.17, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-09", "tag": "PA-204", "category": "luminaire", "center": [ 1079.76, 409.27 ], "sourcePDFPoint": [ 1457.67, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-10", "tag": "PA-204", "category": "luminaire", "center": [ 1160.87, 409.27 ], "sourcePDFPoint": [ 1567.17, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-11", "tag": "PA-204", "category": "luminaire", "center": [ 1248.64, 409.27 ], "sourcePDFPoint": [ 1685.67, 552.51 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-OS-01", "tag": "OS", "category": "lighting_control", "center": [ 429.63, 418.52 ], "sourcePDFPoint": [ 580, 565 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-OS-02", "tag": "OS", "category": "lighting_control", "center": [ 629.63, 418.52 ], "sourcePDFPoint": [ 850, 565 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-OS-03", "tag": "OS", "category": "lighting_control", "center": [ 829.63, 418.52 ], "sourcePDFPoint": [ 1120, 565 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-OS-04", "tag": "OS", "category": "lighting_control", "center": [ 1029.63, 418.52 ], "sourcePDFPoint": [ 1390, 565 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-OS-05", "tag": "OS", "category": "lighting_control", "center": [ 1229.63, 418.52 ], "sourcePDFPoint": [ 1660, 565 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-OS-06", "tag": "OS", "category": "lighting_control", "center": [ 1377.78, 418.52 ], "sourcePDFPoint": [ 1860, 565 ], "status": "counted_plotted_occurrence", "note": "Six corridor occupancy sensors keyed 2 plus one elevator-lobby occupancy sensor keyed 2." }, { "id": "E23-X1-01", "tag": "X1", "category": "exit_sign", "center": [ 294.82, 422.6 ], "sourcePDFPoint": [ 398.01, 570.51 ], "status": "counted_plotted_occurrence", "note": "Single-face exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-R11-01", "tag": "R11", "category": "luminaire", "center": [ 341.91, 422.6 ], "sourcePDFPoint": [ 461.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-02", "tag": "R11", "category": "luminaire", "center": [ 408.58, 422.6 ], "sourcePDFPoint": [ 551.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-03", "tag": "R11", "category": "luminaire", "center": [ 475.24, 422.6 ], "sourcePDFPoint": [ 641.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-04", "tag": "R11", "category": "luminaire", "center": [ 541.91, 422.6 ], "sourcePDFPoint": [ 731.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-05", "tag": "R11", "category": "luminaire", "center": [ 608.58, 422.6 ], "sourcePDFPoint": [ 821.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-06", "tag": "R11", "category": "luminaire", "center": [ 675.24, 422.6 ], "sourcePDFPoint": [ 911.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-07", "tag": "R11", "category": "luminaire", "center": [ 741.91, 422.6 ], "sourcePDFPoint": [ 1001.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-08", "tag": "R11", "category": "luminaire", "center": [ 808.58, 422.6 ], "sourcePDFPoint": [ 1091.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-09", "tag": "R11", "category": "luminaire", "center": [ 875.24, 422.6 ], "sourcePDFPoint": [ 1181.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-X2-01", "tag": "X2", "category": "exit_sign", "center": [ 881.98, 422.6 ], "sourcePDFPoint": [ 1190.67, 570.51 ], "status": "counted_plotted_occurrence", "note": "Two-face exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-R11-10", "tag": "R11", "category": "luminaire", "center": [ 941.91, 422.6 ], "sourcePDFPoint": [ 1271.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-11", "tag": "R11", "category": "luminaire", "center": [ 1008.58, 422.6 ], "sourcePDFPoint": [ 1361.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-12", "tag": "R11", "category": "luminaire", "center": [ 1075.24, 422.6 ], "sourcePDFPoint": [ 1451.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-13", "tag": "R11", "category": "luminaire", "center": [ 1141.91, 422.6 ], "sourcePDFPoint": [ 1541.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-14", "tag": "R11", "category": "luminaire", "center": [ 1208.58, 422.6 ], "sourcePDFPoint": [ 1631.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-15", "tag": "R11", "category": "luminaire", "center": [ 1275.24, 422.6 ], "sourcePDFPoint": [ 1721.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-X2-02", "tag": "X2", "category": "exit_sign", "center": [ 1333.09, 422.6 ], "sourcePDFPoint": [ 1799.67, 570.51 ], "status": "counted_plotted_occurrence", "note": "Two-face exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-R11-16", "tag": "R11", "category": "luminaire", "center": [ 1341.91, 422.6 ], "sourcePDFPoint": [ 1811.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-R11-17", "tag": "R11", "category": "luminaire", "center": [ 1408.58, 422.6 ], "sourcePDFPoint": [ 1901.58, 570.51 ], "status": "counted_plotted_occurrence", "note": "17 corridor downlights plus 4 elevator-lobby downlights." }, { "id": "E23-X1-03", "tag": "X1", "category": "exit_sign", "center": [ 1447.04, 422.6 ], "sourcePDFPoint": [ 1953.51, 570.51 ], "status": "counted_plotted_occurrence", "note": "Single-face exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-EM-01", "tag": "EM", "category": "emergency_lighting", "center": [ 364.44, 431.11 ], "sourcePDFPoint": [ 492, 582 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-EM-03", "tag": "EM", "category": "emergency_lighting", "center": [ 764.44, 431.11 ], "sourcePDFPoint": [ 1032, 582 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-EM-05", "tag": "EM", "category": "emergency_lighting", "center": [ 1164.44, 431.11 ], "sourcePDFPoint": [ 1572, 582 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-PA204-12", "tag": "PA-204", "category": "luminaire", "center": [ 428.51, 435.67 ], "sourcePDFPoint": [ 578.49, 588.15 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-13", "tag": "PA-204", "category": "luminaire", "center": [ 485.18, 435.71 ], "sourcePDFPoint": [ 654.99, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-14", "tag": "PA-204", "category": "luminaire", "center": [ 572.91, 435.71 ], "sourcePDFPoint": [ 773.43, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-15", "tag": "PA-204", "category": "luminaire", "center": [ 654.07, 435.71 ], "sourcePDFPoint": [ 882.99, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-16", "tag": "PA-204", "category": "luminaire", "center": [ 741.8, 435.71 ], "sourcePDFPoint": [ 1001.43, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-17", "tag": "PA-204", "category": "luminaire", "center": [ 822.96, 435.71 ], "sourcePDFPoint": [ 1110.99, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-18", "tag": "PA-204", "category": "luminaire", "center": [ 910.69, 435.71 ], "sourcePDFPoint": [ 1229.43, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-19", "tag": "PA-204", "category": "luminaire", "center": [ 996.33, 435.71 ], "sourcePDFPoint": [ 1345.05, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-20", "tag": "PA-204", "category": "luminaire", "center": [ 1075.09, 435.71 ], "sourcePDFPoint": [ 1451.37, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-21", "tag": "PA-204", "category": "luminaire", "center": [ 1165.62, 435.71 ], "sourcePDFPoint": [ 1573.59, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-22", "tag": "PA-204", "category": "luminaire", "center": [ 1243.53, 435.71 ], "sourcePDFPoint": [ 1678.77, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-23", "tag": "PA-204", "category": "luminaire", "center": [ 1329.67, 435.71 ], "sourcePDFPoint": [ 1795.05, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-PA204-24", "tag": "PA-204", "category": "luminaire", "center": [ 1419.8, 435.71 ], "sourcePDFPoint": [ 1916.73, 588.21 ], "status": "counted_plotted_occurrence", "note": "Corridor/east-wall wall sconce; tag identity reconciled to E2.0 schedule." }, { "id": "E23-X3-01", "tag": "X3", "category": "exit_sign", "center": [ 309.93, 436.2 ], "sourcePDFPoint": [ 418.41, 588.87 ], "status": "counted_plotted_occurrence", "note": "Wall exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-X3-02", "tag": "X3", "category": "exit_sign", "center": [ 867.62, 436.2 ], "sourcePDFPoint": [ 1171.29, 588.87 ], "status": "counted_plotted_occurrence", "note": "Wall exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-X3-04", "tag": "X3", "category": "exit_sign", "center": [ 1321.4, 436.2 ], "sourcePDFPoint": [ 1783.89, 588.87 ], "status": "counted_plotted_occurrence", "note": "Wall exit sign tag as reconciled to E2.0 legend." }, { "id": "E23-EM-07", "tag": "EM", "category": "emergency_lighting", "center": [ 314.67, 447.11 ], "sourcePDFPoint": [ 424.8, 603.6 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." }, { "id": "E23-HOMERUN-01", "tag": "HOME-RUN", "category": "circuit_callout", "center": [ 1085.19, 452.59 ], "sourcePDFPoint": [ 1465, 611 ], "status": "counted_plotted_occurrence", "note": "One visible home-run arrow/circuit callout: L1.B-25,27; arrow/ticks not measured as panel routing." }, { "id": "E23-S02-01", "tag": "S02", "category": "luminaire", "center": [ 288.89, 471.11 ], "sourcePDFPoint": [ 390.0, 636.0 ], "status": "counted_plotted_occurrence", "note": "Two fixtures in each stair; keynote 1." }, { "id": "E23-S02-02", "tag": "S02", "category": "luminaire", "center": [ 391.11, 471.11 ], "sourcePDFPoint": [ 528.0, 636.0 ], "status": "counted_plotted_occurrence", "note": "Two fixtures in each stair; keynote 1." }, { "id": "E23-EM-08", "tag": "EM", "category": "emergency_lighting", "center": [ 376.89, 487.11 ], "sourcePDFPoint": [ 508.8, 657.6 ], "status": "counted_plotted_occurrence", "note": "Six corridor, two Stair 2, two Stair 1, and one Storage emergency units." } ], "wiring": { "status": "VISIBLE DRAWN CONNECTION MEASUREMENT — NOT INSTALLED ROUTING OR CONDUCTOR TAKEOFF", "circuitCallouts": [ { "text": "L1.B-25,27", "center": [ 1085.19, 452.59 ], "occurrences": 1, "routeBeyondArrowMeasured": false }, { "text": "L1.B-33", "source": "keyed note 1", "occurrences": 1, "planRouteDrawn": false, "conductorsPrinted": "2#10", "conduitPrinted": "1/2 inch C" } ], "runs": [ { "id": "W01", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22529, "sourceSeqno": 22879, "polylineNormalized": [ [ 316.32, 409.26 ], [ 318.39, 412.58 ], [ 320.9, 415.49 ], [ 323.8, 417.96 ], [ 327.02, 419.96 ], [ 330.5, 421.45 ], [ 334.18, 422.4 ], [ 338.01, 422.79 ], [ 341.92, 422.59 ] ], "drawnPathLFRaw": 4.611, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W02", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22530, "sourceSeqno": 22880, "polylineNormalized": [ [ 341.91, 422.58 ], [ 345.0, 428.39 ], [ 348.75, 433.69 ], [ 353.09, 438.46 ], [ 357.97, 442.65 ], [ 363.33, 446.2 ], [ 369.1, 449.08 ], [ 375.24, 451.23 ], [ 381.66, 452.62 ], [ 388.21, 453.19 ], [ 394.7, 452.94 ], [ 401.07, 451.89 ], [ 407.24, 450.07 ], [ 413.13, 447.52 ], [ 418.69, 444.24 ], [ 423.83, 440.27 ], [ 428.5, 435.64 ] ], "drawnPathLFRaw": 15.58, "drawnPathLFRounded0_5": 15.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W03", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22531, "sourceSeqno": 22881, "polylineNormalized": [ [ 408.6, 422.6 ], [ 409.84, 425.67 ], [ 411.57, 428.4 ], [ 413.71, 430.77 ], [ 416.21, 432.73 ], [ 419.0, 434.24 ], [ 422.02, 435.25 ], [ 425.22, 435.74 ], [ 428.53, 435.66 ] ], "drawnPathLFRaw": 3.878, "drawnPathLFRounded0_5": 4.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W04", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22532, "sourceSeqno": 22882, "polylineNormalized": [ [ 404.19, 409.25 ], [ 403.63, 410.12 ], [ 403.18, 411.04 ], [ 402.85, 412.01 ], [ 402.64, 413.0 ], [ 402.54, 414.0 ], [ 402.56, 415.02 ], [ 402.7, 416.03 ], [ 402.97, 417.03 ], [ 403.35, 418.0 ], [ 403.84, 418.9 ], [ 404.42, 419.73 ], [ 405.1, 420.48 ], [ 405.86, 421.15 ], [ 406.7, 421.73 ], [ 407.6, 422.2 ], [ 408.57, 422.57 ] ], "drawnPathLFRaw": 2.455, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W05", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22533, "sourceSeqno": 22883, "polylineNormalized": [ [ 294.84, 422.58 ], [ 298.34, 422.74 ], [ 301.74, 422.29 ], [ 304.97, 421.28 ], [ 307.96, 419.76 ], [ 310.65, 417.75 ], [ 312.99, 415.31 ], [ 314.89, 412.46 ], [ 316.31, 409.26 ] ], "drawnPathLFRaw": 4.106, "drawnPathLFRounded0_5": 4.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W06", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22534, "sourceSeqno": 22884, "polylineNormalized": [ [ 294.83, 422.57 ], [ 294.76, 424.07 ], [ 294.86, 425.55 ], [ 295.14, 427.0 ], [ 295.58, 428.41 ], [ 296.18, 429.75 ], [ 296.94, 431.02 ], [ 297.85, 432.19 ], [ 298.91, 433.26 ], [ 300.08, 434.2 ], [ 301.34, 434.98 ], [ 302.68, 435.6 ], [ 304.08, 436.07 ], [ 305.52, 436.36 ], [ 306.99, 436.49 ], [ 308.48, 436.43 ], [ 309.96, 436.21 ] ], "drawnPathLFRaw": 3.563, "drawnPathLFRounded0_5": 3.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W07", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22535, "sourceSeqno": 22885, "polylineNormalized": [ [ 485.35, 409.25 ], [ 475.77, 404.07 ], [ 465.71, 400.38 ], [ 455.33, 398.16 ], [ 444.78, 397.42 ], [ 434.23, 398.16 ], [ 423.84, 400.38 ], [ 413.78, 404.07 ], [ 404.2, 409.25 ] ], "drawnPathLFRaw": 12.851, "drawnPathLFRounded0_5": 13.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W08", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22536, "sourceSeqno": 22886, "polylineNormalized": [ [ 475.26, 422.57 ], [ 476.46, 422.47 ], [ 477.63, 422.23 ], [ 478.77, 421.86 ], [ 479.85, 421.38 ], [ 480.87, 420.77 ], [ 481.82, 420.06 ], [ 482.69, 419.24 ], [ 483.47, 418.32 ], [ 484.14, 417.32 ], [ 484.7, 416.26 ], [ 485.12, 415.15 ], [ 485.43, 414.0 ], [ 485.6, 412.83 ], [ 485.64, 411.64 ], [ 485.55, 410.45 ], [ 485.33, 409.26 ] ], "drawnPathLFRaw": 2.868, "drawnPathLFRounded0_5": 3.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W09", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22537, "sourceSeqno": 22887, "polylineNormalized": [ [ 475.25, 422.6 ], [ 474.65, 423.79 ], [ 474.25, 425.04 ], [ 474.04, 426.33 ], [ 474.01, 427.62 ], [ 474.18, 428.91 ], [ 474.53, 430.16 ], [ 475.07, 431.36 ], [ 475.79, 432.48 ], [ 476.68, 433.48 ], [ 477.68, 434.33 ], [ 478.79, 435.01 ], [ 479.98, 435.52 ], [ 481.23, 435.85 ], [ 482.53, 435.99 ], [ 483.84, 435.95 ], [ 485.16, 435.7 ] ], "drawnPathLFRaw": 3.151, "drawnPathLFRounded0_5": 3.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W10", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22538, "sourceSeqno": 22888, "polylineNormalized": [ [ 541.92, 422.58 ], [ 534.39, 420.85 ], [ 526.8, 420.12 ], [ 519.23, 420.37 ], [ 511.79, 421.6 ], [ 504.57, 423.76 ], [ 497.66, 426.85 ], [ 491.16, 430.84 ], [ 485.16, 435.71 ] ], "drawnPathLFRaw": 9.145, "drawnPathLFRounded0_5": 9.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W11", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22539, "sourceSeqno": 22889, "polylineNormalized": [ [ 572.92, 435.71 ], [ 571.99, 433.53 ], [ 570.84, 431.47 ], [ 569.5, 429.54 ], [ 567.97, 427.77 ], [ 566.27, 426.16 ], [ 564.41, 424.73 ], [ 562.41, 423.49 ], [ 560.27, 422.45 ], [ 558.03, 421.64 ], [ 555.75, 421.06 ], [ 553.43, 420.72 ], [ 551.09, 420.62 ], [ 548.75, 420.76 ], [ 546.43, 421.13 ], [ 544.16, 421.74 ], [ 541.94, 422.59 ] ], "drawnPathLFRaw": 5.655, "drawnPathLFRounded0_5": 5.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W12", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22540, "sourceSeqno": 22890, "polylineNormalized": [ [ 586.99, 409.14 ], [ 584.85, 409.65 ], [ 582.8, 410.39 ], [ 580.86, 411.35 ], [ 579.05, 412.53 ], [ 577.38, 413.9 ], [ 575.87, 415.45 ], [ 574.54, 417.18 ], [ 573.4, 419.06 ], [ 572.49, 421.06 ], [ 571.82, 423.14 ], [ 571.39, 425.26 ], [ 571.21, 427.41 ], [ 571.27, 429.57 ], [ 571.57, 431.71 ], [ 572.11, 433.82 ], [ 572.91, 435.88 ] ], "drawnPathLFRaw": 5.225, "drawnPathLFRounded0_5": 5.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W13", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22541, "sourceSeqno": 22891, "polylineNormalized": [ [ 587.04, 409.24 ], [ 588.34, 412.57 ], [ 590.19, 415.52 ], [ 592.52, 418.04 ], [ 595.24, 420.08 ], [ 598.29, 421.6 ], [ 601.58, 422.55 ], [ 605.04, 422.89 ], [ 608.6, 422.57 ] ], "drawnPathLFRaw": 4.171, "drawnPathLFRounded0_5": 4.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W14", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22542, "sourceSeqno": 22892, "polylineNormalized": [ [ 358.88, 435.98 ], [ 358.74, 434.43 ], [ 358.43, 432.93 ], [ 357.97, 431.47 ], [ 357.35, 430.08 ], [ 356.59, 428.76 ], [ 355.69, 427.53 ], [ 354.65, 426.4 ], [ 353.49, 425.37 ], [ 352.23, 424.48 ], [ 350.88, 423.73 ], [ 349.48, 423.14 ], [ 348.02, 422.71 ], [ 346.52, 422.43 ], [ 345.0, 422.31 ], [ 343.46, 422.36 ], [ 341.93, 422.58 ] ], "drawnPathLFRaw": 3.682, "drawnPathLFRounded0_5": 3.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W15", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22543, "sourceSeqno": 22893, "polylineNormalized": [ [ 541.92, 422.59 ], [ 542.5, 421.69 ], [ 542.98, 420.75 ], [ 543.35, 419.77 ], [ 543.63, 418.76 ], [ 543.8, 417.73 ], [ 543.87, 416.68 ], [ 543.82, 415.62 ], [ 543.67, 414.57 ], [ 543.42, 413.54 ], [ 543.06, 412.55 ], [ 542.6, 411.6 ], [ 542.05, 410.71 ], [ 541.42, 409.88 ], [ 540.7, 409.11 ], [ 539.9, 408.42 ], [ 539.03, 407.81 ] ], "drawnPathLFRaw": 2.531, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W16", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22544, "sourceSeqno": 22894, "polylineNormalized": [ [ 608.57, 422.59 ], [ 612.8, 427.59 ], [ 617.71, 431.69 ], [ 623.17, 434.87 ], [ 629.04, 437.07 ], [ 635.21, 438.27 ], [ 641.52, 438.43 ], [ 647.85, 437.5 ], [ 654.07, 435.45 ] ], "drawnPathLFRaw": 7.669, "drawnPathLFRounded0_5": 7.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W17", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22545, "sourceSeqno": 22895, "polylineNormalized": [ [ 675.24, 422.62 ], [ 671.78, 422.31 ], [ 668.41, 422.64 ], [ 665.2, 423.55 ], [ 662.22, 425.02 ], [ 659.55, 426.98 ], [ 657.25, 429.41 ], [ 655.4, 432.25 ], [ 654.07, 435.46 ] ], "drawnPathLFRaw": 4.062, "drawnPathLFRounded0_5": 4.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W18", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22546, "sourceSeqno": 22896, "polylineNormalized": [ [ 741.82, 435.72 ], [ 734.41, 430.88 ], [ 726.59, 426.93 ], [ 718.43, 423.87 ], [ 710.01, 421.73 ], [ 701.41, 420.51 ], [ 692.7, 420.24 ], [ 683.96, 420.94 ], [ 675.27, 422.6 ] ], "drawnPathLFRaw": 10.51, "drawnPathLFRounded0_5": 10.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W19", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22547, "sourceSeqno": 22897, "polylineNormalized": [ [ 675.25, 422.59 ], [ 675.32, 424.35 ], [ 675.6, 426.08 ], [ 676.07, 427.75 ], [ 676.73, 429.34 ], [ 677.57, 430.86 ], [ 678.58, 432.27 ], [ 679.75, 433.56 ], [ 681.08, 434.72 ], [ 682.54, 435.72 ], [ 684.08, 436.53 ], [ 685.7, 437.15 ], [ 687.37, 437.58 ], [ 689.09, 437.82 ], [ 690.82, 437.86 ], [ 692.56, 437.69 ], [ 694.28, 437.33 ] ], "drawnPathLFRaw": 4.186, "drawnPathLFRounded0_5": 4.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W20", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22548, "sourceSeqno": 22898, "polylineNormalized": [ [ 741.8, 435.85 ], [ 742.51, 435.21 ], [ 743.14, 434.5 ], [ 743.68, 433.73 ], [ 744.13, 432.9 ], [ 744.49, 432.04 ], [ 744.75, 431.13 ], [ 744.92, 430.2 ], [ 744.98, 429.25 ], [ 744.93, 428.29 ], [ 744.78, 427.36 ], [ 744.53, 426.45 ], [ 744.19, 425.58 ], [ 743.75, 424.75 ], [ 743.22, 423.97 ], [ 742.61, 423.25 ], [ 741.91, 422.59 ] ], "drawnPathLFRaw": 2.271, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W21", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22549, "sourceSeqno": 22899, "polylineNormalized": [ [ 741.9, 409.28 ], [ 740.72, 409.58 ], [ 739.64, 410.07 ], [ 738.67, 410.74 ], [ 737.84, 411.56 ], [ 737.16, 412.51 ], [ 736.65, 413.57 ], [ 736.33, 414.72 ], [ 736.22, 415.93 ], [ 736.33, 417.15 ], [ 736.65, 418.3 ], [ 737.16, 419.36 ], [ 737.84, 420.31 ], [ 738.67, 421.13 ], [ 739.64, 421.79 ], [ 740.72, 422.29 ], [ 741.9, 422.58 ] ], "drawnPathLFRaw": 2.857, "drawnPathLFRounded0_5": 3.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W22", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22550, "sourceSeqno": 22900, "polylineNormalized": [ [ 808.56, 422.62 ], [ 806.07, 418.38 ], [ 803.14, 414.48 ], [ 799.81, 410.95 ], [ 796.13, 407.83 ], [ 792.12, 405.13 ], [ 787.82, 402.89 ], [ 783.27, 401.13 ], [ 778.51, 399.89 ], [ 773.64, 399.18 ], [ 768.76, 399.04 ], [ 763.93, 399.43 ], [ 759.19, 400.36 ], [ 754.58, 401.8 ], [ 750.15, 403.76 ], [ 745.93, 406.21 ], [ 741.99, 409.15 ] ], "drawnPathLFRaw": 11.692, "drawnPathLFRounded0_5": 11.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W23", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22551, "sourceSeqno": 22901, "polylineNormalized": [ [ 808.56, 422.59 ], [ 808.13, 424.11 ], [ 807.93, 425.66 ], [ 807.95, 427.21 ], [ 808.21, 428.73 ], [ 808.67, 430.2 ], [ 809.35, 431.58 ], [ 810.24, 432.87 ], [ 811.32, 434.03 ], [ 812.56, 435.02 ], [ 813.92, 435.8 ], [ 815.36, 436.37 ], [ 816.86, 436.71 ], [ 818.39, 436.84 ], [ 819.93, 436.75 ], [ 821.46, 436.43 ], [ 822.95, 435.87 ] ], "drawnPathLFRaw": 3.745, "drawnPathLFRounded0_5": 3.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W24", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22552, "sourceSeqno": 22902, "polylineNormalized": [ [ 823.09, 409.25 ], [ 820.67, 412.19 ], [ 818.93, 415.46 ], [ 817.88, 418.94 ], [ 817.51, 422.53 ], [ 817.83, 426.13 ], [ 818.84, 429.62 ], [ 820.54, 432.91 ], [ 822.93, 435.88 ] ], "drawnPathLFRaw": 4.434, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W25", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22553, "sourceSeqno": 22903, "polylineNormalized": [ [ 823.1, 409.11 ], [ 828.16, 414.49 ], [ 833.9, 418.89 ], [ 840.2, 422.26 ], [ 846.92, 424.58 ], [ 853.92, 425.8 ], [ 861.07, 425.91 ], [ 868.22, 424.85 ], [ 875.25, 422.59 ] ], "drawnPathLFRaw": 8.669, "drawnPathLFRounded0_5": 8.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W26", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22554, "sourceSeqno": 22904, "polylineNormalized": [ [ 875.26, 422.61 ], [ 876.01, 420.58 ], [ 876.37, 418.5 ], [ 876.34, 416.42 ], [ 875.94, 414.39 ], [ 875.18, 412.47 ], [ 874.08, 410.71 ], [ 872.65, 409.15 ], [ 870.92, 407.85 ] ], "drawnPathLFRaw": 2.531, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W27", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22556, "sourceSeqno": 22906, "polylineNormalized": [ [ 867.62, 436.18 ], [ 869.06, 436.34 ], [ 870.49, 436.33 ], [ 871.9, 436.15 ], [ 873.28, 435.82 ], [ 874.61, 435.33 ], [ 875.88, 434.68 ], [ 877.08, 433.89 ], [ 878.18, 432.96 ], [ 879.17, 431.91 ], [ 880.03, 430.76 ], [ 880.73, 429.52 ], [ 881.3, 428.22 ], [ 881.7, 426.86 ], [ 881.96, 425.46 ], [ 882.04, 424.03 ], [ 881.97, 422.58 ] ], "drawnPathLFRaw": 3.435, "drawnPathLFRounded0_5": 3.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W28", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22557, "sourceSeqno": 22907, "polylineNormalized": [ [ 910.88, 409.1 ], [ 905.86, 408.67 ], [ 900.88, 408.89 ], [ 896.01, 409.74 ], [ 891.3, 411.19 ], [ 886.82, 413.22 ], [ 882.61, 415.81 ], [ 878.73, 418.93 ], [ 875.25, 422.58 ] ], "drawnPathLFRaw": 5.971, "drawnPathLFRounded0_5": 6.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W29", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22558, "sourceSeqno": 22908, "polylineNormalized": [ [ 910.87, 409.28 ], [ 909.56, 410.62 ], [ 908.4, 412.08 ], [ 907.4, 413.65 ], [ 906.57, 415.3 ], [ 905.91, 417.03 ], [ 905.43, 418.82 ], [ 905.13, 420.66 ], [ 905.02, 422.53 ], [ 905.11, 424.41 ], [ 905.38, 426.25 ], [ 905.84, 428.05 ], [ 906.48, 429.78 ], [ 907.29, 431.45 ], [ 908.27, 433.02 ], [ 909.41, 434.5 ], [ 910.71, 435.86 ] ], "drawnPathLFRaw": 4.47, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W30", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22559, "sourceSeqno": 22909, "polylineNormalized": [ [ 941.92, 422.57 ], [ 937.26, 421.31 ], [ 932.58, 420.98 ], [ 928.0, 421.54 ], [ 923.64, 422.93 ], [ 919.6, 425.11 ], [ 916.02, 428.02 ], [ 913.01, 431.61 ], [ 910.69, 435.84 ] ], "drawnPathLFRaw": 5.623, "drawnPathLFRounded0_5": 5.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W31", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22560, "sourceSeqno": 22910, "polylineNormalized": [ [ 941.93, 422.58 ], [ 943.95, 426.04 ], [ 946.31, 429.24 ], [ 948.98, 432.15 ], [ 951.94, 434.75 ], [ 955.16, 437.03 ], [ 958.61, 438.95 ], [ 962.27, 440.5 ], [ 966.1, 441.66 ], [ 970.04, 442.4 ], [ 974.01, 442.7 ], [ 977.96, 442.58 ], [ 981.86, 442.04 ], [ 985.68, 441.09 ], [ 989.4, 439.74 ], [ 992.96, 437.98 ], [ 996.34, 435.84 ] ], "drawnPathLFRaw": 9.528, "drawnPathLFRounded0_5": 9.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W32", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22561, "sourceSeqno": 22911, "polylineNormalized": [ [ 992.02, 409.27 ], [ 990.97, 410.85 ], [ 990.09, 412.5 ], [ 989.38, 414.24 ], [ 988.85, 416.02 ], [ 988.49, 417.86 ], [ 988.33, 419.72 ], [ 988.35, 421.6 ], [ 988.56, 423.48 ], [ 988.95, 425.33 ], [ 989.53, 427.12 ], [ 990.28, 428.83 ], [ 991.2, 430.46 ], [ 992.27, 431.99 ], [ 993.49, 433.4 ], [ 994.86, 434.69 ], [ 996.36, 435.85 ] ], "drawnPathLFRaw": 4.507, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W33", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22562, "sourceSeqno": 22912, "polylineNormalized": [ [ 991.97, 409.24 ], [ 992.11, 410.76 ], [ 992.42, 412.23 ], [ 992.87, 413.66 ], [ 993.48, 415.03 ], [ 994.22, 416.33 ], [ 995.1, 417.54 ], [ 996.11, 418.66 ], [ 997.24, 419.68 ], [ 998.47, 420.56 ], [ 999.78, 421.31 ], [ 1001.16, 421.91 ], [ 1002.59, 422.35 ], [ 1004.05, 422.65 ], [ 1005.54, 422.79 ], [ 1007.05, 422.77 ], [ 1008.56, 422.59 ] ], "drawnPathLFRaw": 3.615, "drawnPathLFRounded0_5": 3.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W34", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22563, "sourceSeqno": 22913, "polylineNormalized": [ [ 1075.08, 435.73 ], [ 1068.52, 428.97 ], [ 1061.05, 423.59 ], [ 1052.87, 419.63 ], [ 1044.2, 417.14 ], [ 1035.22, 416.15 ], [ 1026.16, 416.7 ], [ 1017.2, 418.84 ], [ 1008.56, 422.6 ] ], "drawnPathLFRaw": 11.037, "drawnPathLFRounded0_5": 11.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W35", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22564, "sourceSeqno": 22914, "polylineNormalized": [ [ 1075.07, 435.84 ], [ 1075.73, 435.17 ], [ 1076.32, 434.45 ], [ 1076.82, 433.67 ], [ 1077.24, 432.85 ], [ 1077.58, 431.99 ], [ 1077.83, 431.1 ], [ 1077.98, 430.18 ], [ 1078.04, 429.24 ], [ 1078.01, 428.31 ], [ 1077.87, 427.38 ], [ 1077.65, 426.49 ], [ 1077.33, 425.62 ], [ 1076.93, 424.78 ], [ 1076.44, 424.0 ], [ 1075.88, 423.26 ], [ 1075.23, 422.58 ] ], "drawnPathLFRaw": 2.233, "drawnPathLFRounded0_5": 2.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W36", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22565, "sourceSeqno": 22915, "polylineNormalized": [ [ 1075.24, 422.6 ], [ 1076.13, 422.14 ], [ 1076.97, 421.61 ], [ 1077.74, 420.99 ], [ 1078.43, 420.3 ], [ 1079.06, 419.54 ], [ 1079.6, 418.72 ], [ 1080.06, 417.84 ], [ 1080.43, 416.91 ], [ 1080.7, 415.95 ], [ 1080.87, 414.97 ], [ 1080.93, 413.99 ], [ 1080.9, 413.0 ], [ 1080.76, 412.03 ], [ 1080.52, 411.07 ], [ 1080.19, 410.14 ], [ 1079.75, 409.24 ] ], "drawnPathLFRaw": 2.377, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W37", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22566, "sourceSeqno": 22916, "polylineNormalized": [ [ 1079.75, 409.13 ], [ 1086.45, 414.18 ], [ 1093.64, 418.31 ], [ 1101.23, 421.5 ], [ 1109.13, 423.73 ], [ 1117.24, 424.97 ], [ 1125.47, 425.21 ], [ 1133.73, 424.43 ], [ 1141.92, 422.61 ] ], "drawnPathLFRaw": 9.943, "drawnPathLFRounded0_5": 10.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W38", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22567, "sourceSeqno": 22917, "polylineNormalized": [ [ 1075.23, 435.72 ], [ 1071.06, 433.06 ], [ 1066.59, 431.23 ], [ 1061.94, 430.22 ], [ 1057.21, 430.03 ], [ 1052.52, 430.65 ], [ 1047.97, 432.08 ], [ 1043.69, 434.31 ], [ 1039.78, 437.34 ] ], "drawnPathLFRaw": 5.789, "drawnPathLFRounded0_5": 6.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W39", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22568, "sourceSeqno": 22918, "polylineNormalized": [ [ 1141.92, 422.63 ], [ 1145.22, 422.83 ], [ 1148.4, 422.4 ], [ 1151.4, 421.38 ], [ 1154.12, 419.82 ], [ 1156.51, 417.78 ], [ 1158.49, 415.31 ], [ 1159.98, 412.46 ], [ 1160.91, 409.29 ] ], "drawnPathLFRaw": 3.854, "drawnPathLFRounded0_5": 4.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W40", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22569, "sourceSeqno": 22919, "polylineNormalized": [ [ 1165.62, 435.7 ], [ 1166.82, 434.16 ], [ 1167.82, 432.5 ], [ 1168.63, 430.76 ], [ 1169.24, 428.94 ], [ 1169.65, 427.07 ], [ 1169.85, 425.15 ], [ 1169.83, 423.22 ], [ 1169.6, 421.28 ], [ 1169.15, 419.38 ], [ 1168.49, 417.56 ], [ 1167.64, 415.83 ], [ 1166.61, 414.22 ], [ 1165.41, 412.72 ], [ 1164.05, 411.37 ], [ 1162.53, 410.16 ], [ 1160.88, 409.13 ] ], "drawnPathLFRaw": 4.639, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W41", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22570, "sourceSeqno": 22920, "polylineNormalized": [ [ 1165.65, 435.71 ], [ 1168.46, 437.23 ], [ 1171.4, 438.42 ], [ 1174.43, 439.3 ], [ 1177.52, 439.86 ], [ 1180.66, 440.08 ], [ 1183.81, 439.98 ], [ 1186.95, 439.55 ], [ 1190.06, 438.78 ], [ 1193.06, 437.68 ], [ 1195.91, 436.28 ], [ 1198.58, 434.61 ], [ 1201.05, 432.66 ], [ 1203.31, 430.47 ], [ 1205.33, 428.05 ], [ 1207.09, 425.42 ], [ 1208.58, 422.59 ] ], "drawnPathLFRaw": 7.604, "drawnPathLFRounded0_5": 7.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W42", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22571, "sourceSeqno": 22921, "polylineNormalized": [ [ 1208.6, 422.61 ], [ 1209.41, 421.91 ], [ 1210.13, 421.12 ], [ 1210.76, 420.27 ], [ 1211.28, 419.35 ], [ 1211.7, 418.38 ], [ 1212.01, 417.37 ], [ 1212.2, 416.32 ], [ 1212.27, 415.25 ], [ 1212.21, 414.17 ], [ 1212.04, 413.12 ], [ 1211.75, 412.1 ], [ 1211.34, 411.13 ], [ 1210.83, 410.2 ], [ 1210.22, 409.34 ], [ 1209.51, 408.55 ], [ 1208.7, 407.83 ] ], "drawnPathLFRaw": 2.555, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W43", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22572, "sourceSeqno": 22922, "polylineNormalized": [ [ 1208.58, 422.6 ], [ 1209.72, 424.98 ], [ 1211.08, 427.21 ], [ 1212.66, 429.28 ], [ 1214.43, 431.18 ], [ 1216.39, 432.88 ], [ 1218.52, 434.39 ], [ 1220.8, 435.67 ], [ 1223.21, 436.73 ], [ 1225.73, 437.52 ], [ 1228.29, 438.05 ], [ 1230.88, 438.32 ], [ 1233.48, 438.32 ], [ 1236.06, 438.06 ], [ 1238.61, 437.54 ], [ 1241.11, 436.75 ], [ 1243.53, 435.71 ] ], "drawnPathLFRaw": 6.276, "drawnPathLFRounded0_5": 6.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W44", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22573, "sourceSeqno": 22923, "polylineNormalized": [ [ 1248.61, 409.26 ], [ 1246.93, 410.26 ], [ 1245.39, 411.44 ], [ 1244.0, 412.77 ], [ 1242.77, 414.24 ], [ 1241.72, 415.84 ], [ 1240.84, 417.56 ], [ 1240.16, 419.37 ], [ 1239.69, 421.26 ], [ 1239.43, 423.2 ], [ 1239.39, 425.14 ], [ 1239.57, 427.05 ], [ 1239.95, 428.93 ], [ 1240.55, 430.76 ], [ 1241.35, 432.51 ], [ 1242.34, 434.17 ], [ 1243.53, 435.72 ] ], "drawnPathLFRaw": 4.642, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W45", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22574, "sourceSeqno": 22924, "polylineNormalized": [ [ 1248.62, 409.26 ], [ 1249.31, 411.26 ], [ 1250.2, 413.15 ], [ 1251.27, 414.94 ], [ 1252.52, 416.6 ], [ 1253.92, 418.13 ], [ 1255.48, 419.5 ], [ 1257.19, 420.72 ], [ 1259.02, 421.76 ], [ 1260.95, 422.61 ], [ 1262.95, 423.24 ], [ 1264.99, 423.67 ], [ 1267.05, 423.88 ], [ 1269.13, 423.89 ], [ 1271.2, 423.67 ], [ 1273.25, 423.25 ], [ 1275.26, 422.61 ] ], "drawnPathLFRaw": 5.019, "drawnPathLFRounded0_5": 5.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W46", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22575, "sourceSeqno": 22925, "polylineNormalized": [ [ 1275.24, 422.57 ], [ 1277.28, 426.01 ], [ 1279.65, 429.18 ], [ 1282.33, 432.07 ], [ 1285.29, 434.66 ], [ 1288.51, 436.91 ], [ 1291.95, 438.82 ], [ 1295.6, 440.37 ], [ 1299.43, 441.52 ], [ 1303.36, 442.26 ], [ 1307.31, 442.57 ], [ 1311.25, 442.46 ], [ 1315.14, 441.93 ], [ 1318.96, 441.0 ], [ 1322.67, 439.67 ], [ 1326.24, 437.94 ], [ 1329.63, 435.82 ] ], "drawnPathLFRaw": 9.503, "drawnPathLFRounded0_5": 9.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W47", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22576, "sourceSeqno": 22926, "polylineNormalized": [ [ 1329.66, 435.69 ], [ 1331.77, 434.69 ], [ 1333.74, 433.48 ], [ 1335.56, 432.07 ], [ 1337.21, 430.47 ], [ 1338.69, 428.71 ], [ 1339.97, 426.8 ], [ 1341.04, 424.75 ], [ 1341.9, 422.57 ] ], "drawnPathLFRaw": 2.776, "drawnPathLFRounded0_5": 3.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W48", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22577, "sourceSeqno": 22927, "polylineNormalized": [ [ 1333.1, 422.58 ], [ 1334.08, 423.36 ], [ 1335.16, 423.91 ], [ 1336.31, 424.24 ], [ 1337.49, 424.36 ], [ 1338.67, 424.24 ], [ 1339.82, 423.91 ], [ 1340.9, 423.36 ], [ 1341.88, 422.58 ] ], "drawnPathLFRaw": 1.457, "drawnPathLFRounded0_5": 1.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W49", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22578, "sourceSeqno": 22928, "polylineNormalized": [ [ 1333.1, 422.57 ], [ 1331.65, 422.05 ], [ 1330.17, 421.78 ], [ 1328.68, 421.75 ], [ 1327.21, 421.95 ], [ 1325.8, 422.38 ], [ 1324.46, 423.04 ], [ 1323.23, 423.91 ], [ 1322.13, 424.98 ], [ 1321.23, 426.23 ], [ 1320.55, 427.58 ], [ 1320.1, 429.0 ], [ 1319.89, 430.46 ], [ 1319.91, 431.94 ], [ 1320.16, 433.41 ], [ 1320.65, 434.84 ], [ 1321.38, 436.19 ] ], "drawnPathLFRaw": 3.613, "drawnPathLFRounded0_5": 3.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W50", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22579, "sourceSeqno": 22929, "polylineNormalized": [ [ 1341.9, 422.59 ], [ 1344.93, 427.46 ], [ 1348.45, 431.92 ], [ 1352.42, 435.93 ], [ 1356.8, 439.46 ], [ 1361.55, 442.49 ], [ 1366.61, 444.98 ], [ 1371.96, 446.89 ], [ 1377.54, 448.21 ], [ 1383.23, 448.88 ], [ 1388.91, 448.91 ], [ 1394.52, 448.31 ], [ 1400.02, 447.09 ], [ 1405.34, 445.27 ], [ 1410.45, 442.86 ], [ 1415.28, 439.88 ], [ 1419.79, 436.34 ] ], "drawnPathLFRaw": 13.618, "drawnPathLFRounded0_5": 13.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W51", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22580, "sourceSeqno": 22930, "polylineNormalized": [ [ 1419.84, 436.33 ], [ 1425.03, 437.03 ], [ 1430.23, 437.19 ], [ 1435.39, 436.81 ], [ 1440.48, 435.9 ], [ 1445.44, 434.48 ], [ 1450.24, 432.55 ], [ 1454.84, 430.13 ], [ 1459.2, 427.21 ], [ 1463.23, 423.86 ], [ 1466.87, 420.13 ], [ 1470.08, 416.08 ], [ 1472.85, 411.72 ], [ 1475.16, 407.11 ], [ 1476.99, 402.26 ], [ 1478.32, 397.24 ], [ 1479.12, 392.05 ] ], "drawnPathLFRaw": 12.475, "drawnPathLFRounded0_5": 12.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W52", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22581, "sourceSeqno": 22931, "polylineNormalized": [ [ 1408.55, 422.62 ], [ 1413.55, 425.47 ], [ 1418.81, 427.64 ], [ 1424.26, 429.14 ], [ 1429.83, 429.97 ], [ 1435.46, 430.1 ], [ 1441.09, 429.55 ], [ 1446.64, 428.3 ], [ 1452.06, 426.34 ], [ 1457.19, 423.73 ], [ 1461.9, 420.54 ], [ 1466.15, 416.81 ], [ 1469.91, 412.62 ], [ 1473.12, 407.99 ], [ 1475.76, 402.99 ], [ 1477.77, 397.67 ], [ 1479.12, 392.07 ] ], "drawnPathLFRaw": 13.649, "drawnPathLFRounded0_5": 13.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W53", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22582, "sourceSeqno": 22932, "polylineNormalized": [ [ 1395.09, 390.8 ], [ 1393.79, 393.04 ], [ 1392.79, 395.39 ], [ 1392.09, 397.83 ], [ 1391.69, 400.33 ], [ 1391.61, 402.86 ], [ 1391.83, 405.39 ], [ 1392.38, 407.89 ], [ 1393.23, 410.34 ], [ 1394.39, 412.65 ], [ 1395.81, 414.78 ], [ 1397.47, 416.71 ], [ 1399.34, 418.41 ], [ 1401.41, 419.86 ], [ 1403.65, 421.06 ], [ 1406.04, 421.98 ], [ 1408.56, 422.6 ] ], "drawnPathLFRaw": 6.136, "drawnPathLFRounded0_5": 6.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W54", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22583, "sourceSeqno": 22933, "polylineNormalized": [ [ 1447.05, 422.6 ], [ 1442.68, 419.44 ], [ 1437.93, 417.18 ], [ 1432.93, 415.83 ], [ 1427.8, 415.38 ], [ 1422.67, 415.83 ], [ 1417.67, 417.18 ], [ 1412.92, 419.44 ], [ 1408.55, 422.6 ] ], "drawnPathLFRaw": 6.303, "drawnPathLFRounded0_5": 6.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W55", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22592, "sourceSeqno": 22944, "polylineNormalized": [ [ 1462.04, 380.02 ], [ 1458.53, 380.66 ], [ 1455.19, 381.77 ], [ 1452.07, 383.33 ], [ 1449.21, 385.3 ], [ 1446.64, 387.64 ], [ 1444.42, 390.32 ], [ 1442.58, 393.32 ], [ 1441.15, 396.6 ], [ 1440.21, 400.04 ], [ 1439.77, 403.54 ], [ 1439.82, 407.02 ], [ 1440.36, 410.45 ], [ 1441.36, 413.78 ], [ 1442.81, 416.95 ], [ 1444.72, 419.91 ], [ 1447.06, 422.61 ] ], "drawnPathLFRaw": 8.438, "drawnPathLFRounded0_5": 8.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W56", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22593, "sourceSeqno": 22945, "polylineNormalized": [ [ 1362.87, 339.32 ], [ 1360.53, 343.55 ], [ 1358.83, 348.01 ], [ 1357.8, 352.61 ], [ 1357.42, 357.3 ], [ 1357.71, 361.99 ], [ 1358.65, 366.61 ], [ 1360.26, 371.1 ], [ 1362.52, 375.38 ], [ 1365.38, 379.28 ], [ 1368.72, 382.69 ], [ 1372.47, 385.55 ], [ 1376.57, 387.86 ], [ 1380.95, 389.56 ], [ 1385.54, 390.64 ], [ 1390.29, 391.06 ], [ 1395.12, 390.79 ] ], "drawnPathLFRaw": 11.426, "drawnPathLFRounded0_5": 11.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W57", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22594, "sourceSeqno": 22946, "polylineNormalized": [ [ 1301.02, 339.32 ], [ 1308.56, 341.89 ], [ 1316.27, 343.73 ], [ 1324.07, 344.83 ], [ 1331.93, 345.2 ], [ 1339.79, 344.83 ], [ 1347.6, 343.73 ], [ 1355.3, 341.89 ], [ 1362.85, 339.32 ] ], "drawnPathLFRaw": 9.496, "drawnPathLFRounded0_5": 9.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W58", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22595, "sourceSeqno": 22947, "polylineNormalized": [ [ 1301.01, 287.56 ], [ 1297.82, 289.83 ], [ 1294.97, 292.46 ], [ 1292.5, 295.41 ], [ 1290.43, 298.63 ], [ 1288.78, 302.08 ], [ 1287.57, 305.73 ], [ 1286.83, 309.53 ], [ 1286.58, 313.44 ], [ 1286.83, 317.36 ], [ 1287.57, 321.16 ], [ 1288.78, 324.81 ], [ 1290.43, 328.26 ], [ 1292.5, 331.48 ], [ 1294.97, 334.43 ], [ 1297.82, 337.06 ], [ 1301.01, 339.33 ] ], "drawnPathLFRaw": 9.287, "drawnPathLFRounded0_5": 9.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W59", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22596, "sourceSeqno": 22948, "polylineNormalized": [ [ 1301.02, 287.54 ], [ 1308.09, 292.41 ], [ 1315.73, 295.89 ], [ 1323.74, 297.97 ], [ 1331.93, 298.67 ], [ 1340.13, 297.97 ], [ 1348.14, 295.89 ], [ 1355.77, 292.41 ], [ 1362.84, 287.54 ] ], "drawnPathLFRaw": 10.055, "drawnPathLFRounded0_5": 10.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W60", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22597, "sourceSeqno": 22949, "polylineNormalized": [ [ 1333.61, 245.22 ], [ 1333.07, 252.55 ], [ 1333.96, 259.63 ], [ 1336.16, 266.29 ], [ 1339.56, 272.38 ], [ 1344.05, 277.71 ], [ 1349.5, 282.13 ], [ 1355.8, 285.47 ], [ 1362.85, 287.57 ] ], "drawnPathLFRaw": 8.555, "drawnPathLFRounded0_5": 8.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W61", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22598, "sourceSeqno": 22950, "polylineNormalized": [ [ 1333.63, 245.25 ], [ 1331.69, 245.45 ], [ 1329.83, 245.92 ], [ 1328.08, 246.64 ], [ 1326.45, 247.6 ], [ 1324.97, 248.78 ], [ 1323.67, 250.16 ], [ 1322.57, 251.72 ], [ 1321.7, 253.46 ] ], "drawnPathLFRaw": 2.296, "drawnPathLFRounded0_5": 2.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W62", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22599, "sourceSeqno": 22951, "polylineNormalized": [ [ 1333.62, 245.25 ], [ 1329.54, 244.5 ], [ 1325.48, 244.48 ], [ 1321.54, 245.15 ], [ 1317.79, 246.49 ], [ 1314.33, 248.45 ], [ 1311.24, 250.98 ], [ 1308.59, 254.06 ], [ 1306.49, 257.64 ] ], "drawnPathLFRaw": 4.862, "drawnPathLFRounded0_5": 5.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W63", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22600, "sourceSeqno": 22952, "polylineNormalized": [ [ 1362.86, 339.3 ], [ 1356.58, 341.97 ], [ 1350.87, 345.49 ], [ 1345.79, 349.77 ], [ 1341.42, 354.72 ], [ 1337.82, 360.27 ], [ 1335.06, 366.31 ], [ 1333.21, 372.76 ], [ 1332.33, 379.52 ] ], "drawnPathLFRaw": 8.042, "drawnPathLFRounded0_5": 8.0, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" }, { "id": "W64", "group": "L1.B-25,27 drawn lighting connection network", "sourceDrawingIndex": 22612, "sourceSeqno": 22967, "polylineNormalized": [ [ 1333.21, 379.54 ], [ 1334.37, 381.02 ], [ 1335.73, 382.26 ], [ 1337.27, 383.23 ], [ 1338.93, 383.92 ], [ 1340.69, 384.33 ], [ 1342.51, 384.44 ], [ 1344.34, 384.24 ], [ 1346.15, 383.71 ], [ 1347.84, 382.88 ], [ 1349.32, 381.8 ], [ 1350.59, 380.49 ], [ 1351.61, 379.0 ], [ 1352.37, 377.36 ], [ 1352.85, 375.61 ], [ 1353.02, 373.78 ], [ 1352.88, 371.9 ] ], "drawnPathLFRaw": 4.414, "drawnPathLFRounded0_5": 4.5, "circuitAnnotation": "L1.B-25,27", "conductorCount": null, "installedConductorLF": null, "status": "visible drawn connection only" } ], "runCount": 64, "totalDrawnPathLFRaw": 395.616, "totalDrawnPathLFRoundedTo0_5": 395.5, "sumOfIndividuallyRoundedRunLF": 394.5, "notIncluded": [ "Straight home-run arrow and circuit ticks", "Panel-to-home-run routing not visibly drawn", "Unshown vertical rises/drops", "Conductor allocation for L1.B-25 versus L1.B-27", "Equipment whips, switch legs, grounding/control conductors, slack, terminations and waste", "Any guestroom route or fixture inferred from typical sheets E4.0/E4.1" ], "method": "Each visible black vector circuit curve was sampled at 1/8 cubic parameter intervals for saved polylines and integrated at 1/200 intervals for length. PDF point length divided by 9. Runs preserve source drawing/sequence numbers." }, "notes": { "general": [ { "number": 1, "text": "FOR HOME RUNS (FROM UNITS) 100 FT OR MORE, THE ELECTRICAL CONTRACTOR HAS TO CHECK THE VOLTAGE DROP AND SELECT THE SUITABLE CABLES SIZE TO COMPLY WITH THE MAXIMUM ALLOWED VOLTAGE DROP FOR THE BRANCH CIRCUIT (3%)." }, { "number": 2, "text": "THE CONTRACTOR SHALL VERIFY WITH THE OWNER FOR THE APPROVED BRANDS/ MODELS OF THE LOW VOLTAGE SYSTEM DEVICES (CAMERA, CARD READER, WIRELESS ACCESS POINT, ETC.) AND PROVIDE ALL NECESSARY ACCESSORIES TO COMPLETE THE WIRING, POWER SUPPLY FOR THE DEVICES AS PER THE MANUFACTURER SPECIFICATIONS/ INSTALLATION GUIDELINES." }, { "number": 3, "text": "LIGHTING FOR ALL EXTERIOR APPLICATIONS SHALL HAVE AUTOMATIC CONTROLS CAPABLE OF TURNING OFF EXTERIOR LIGHT WHEN SUFFICIENT DAYLIGHT IS AVAILABLE OR WHEN THE LIGHT IS NOT REQUIRED DURING NIGHTTIME HOURS. LIGHTING NOT DESIGNATED FOR DUSK TO DAWN OPERATION SHALL BE CONTROLLED BY AN ASTRONOMICAL TIME SWITCH. LIGHTING DESIGNATED FOR DUSK TO DAWN SHALL BE CONTROLLED BY AN ASTRONOMICAL TIME SWITCH OR PHOTOSENSOR. ASTRONOMICAL TIME SWITCHES SHALL BE CAPABLE OF RETAINING PROGRAMMING AND THE TIME SETTING DURING LOSS OF POWER FOR A PERIOD OF AT LEAST 10 HOURS." }, { "number": 4, "text": "THE OCCUPANCY SENSOR SWITCHES SHALL AUTOMATICALLY TURN LIGHTING ON INSTANTANEOUSLY WHEN THE ROOM/SPACE IS OCCUPIED AND AUTOMATICALLY TURN LIGHTING OFF WITHIN 30 MINUTES OF ALL OCCUPANTS LEAVING THAT ROOM/SPACE." }, { "number": 5, "text": "THE EMERGENCY AND EXIT LIGHTS THAT CONNECT TO LOCAL AREA NORMAL LIGHTING CIRCUITS WILL BE CONNECTED AHEAD OF ANY LOCAL SWITCHES COMPLY WITH NEC 700.12(F)." }, { "number": 6, "text": "EMERGENCY LIGHTING FACILITIES SHALL BE ARRANGE TO PROVIDE INITIAL ILLUMINATION THAT IS AT LEAST 10 FOOT-CANDLES OF EMERGENCY ILLUMINATION SHALL BE PROVIDED ON THE STAIRS AND 1 FOOT-CANDLE ON THE OTHER WALKING SURFACES PER NFPA 101 (SECTION 7.8.1.3 AND 7.9)." }, { "number": 7, "text": "LOW-LEVEL EXIT SIGNS SHALL BE PROVIDED IN ALL AREAS SERVING GUESTROOMS IN GROUP R-1 OCCUPANCIES BY SECTION 1013.1 AND SHALL COMPLY WITH SECTION 1013.5. THE BOTTOM OF THE SIGN SHALL BE NOT LESS THAN 10 INCHES (254MM) NOR MORE THAN 18 INCHES (455MM) ABOVE THE FLOOR LEVEL. THE SIGN SHALL BE FLUSH MOUNTED TO THE DOOR OR WALL. WHERE MOUNTED ON WALL, THE EDGE OF THE SIGN SHALL BE WITHIN 4 INCHES (102MM) OF THE DOOR FRAME ON THE LATCH SIDE." }, { "number": 8, "text": "VERIFY MOUNTING HEIGHT FOR ALL WALL MOUNTED FIXTURE TYPES WITH OWNER/ARCH. PRIOR INSTALLATION." }, { "number": 9, "text": "SEE TYPICAL GUESTROOM PLAN FOR DETAILED ROOM LAYOUT ON SHEETS E4.0, E4.1." }, { "number": 10, "text": "LUMINAIRES INSTALLED IN WET OR DAMP LOCATIONS SHALL BE INSTALLED SUCH THAT WATER CANNOT ENTER OR ACCUMULATE IN WIRING COMPARTMENTS, LAMP HOLDERS, OR OTHER ELECTRICAL PARTS. ALL LUMINAIRES SHALL BE SELECTED SUITABLE FOR WET LOCATIONS OR DAMP LOCATION." }, { "number": 11, "text": "CONTRACTOR SHALL VERIFY AND FURNISH EXIT SIGNS TO COMPLY WITH SECTION 1013 IBC REQUIREMENT." }, { "number": 12, "text": "THE ELECTRICAL CONTRACTOR SHALL COORDINATE WITH THE SPRINKLER CONTRACTOR FOR THE PLACEMENTS OF THE LIGHT FIXTURES AND SPRINKLER HEADS TO COMPLY WITH THE NFPA 13 REQUIREMENTS." }, { "number": 13, "text": "SUFFICIENT EMERGENCY LIGHTING LEVELS WILL BE DETERMINED DURING THE ONSITE INSPECTION. ADDITIONAL EMERGENCY LIGHTING MAY BE REQUIRED BY FIELD INSPECTOR IF DEEMED INSUFFICIENT." } ], "keyed": [ { "number": 1, "text": "CONNECT ALL TYPE \"S02\", \"X1\" & \"X2\" LIGHTS AT STAIRCASE TO L1.B-33 USING 2#10, 1/2\"C. CONTRACTOR WILL PROVIDE A LOCK-ON FEATURE FOR THIS CIRCUIT AS REQUIRED BY NEC 700.12(I)(2)(3).", "planMarkerCount": 8, "quantityInterpretation": "reference bubbles only; not eight circuits or eight fixtures" }, { "number": 2, "text": "OCCUPANT SENSOR CONTROLS IN CORRIDORS SHALL UNIFORMLY REDUCE LIGHTING POWER TO AN UNOCCUPIED SETPOINT NOT MORE THAN 50 PERCENT OF FULL POWER WITHIN 20 MINUTES AFTER ALL OCCUPANTS HAVE LEFT THE SPACE (C405.2.1.4). VERIFY THE DETECTION RANGE OF THE OCCUPANCY SENSORS, AND THE LOCATION AND QUANTITIES OF THE OCCUPANCY SENSORS WITH THE SUPPLIER /MANUFACTURER SPECIFICATIONS & GUIDELINES PRIOR TO INSTALLATION.", "planMarkerCount": 7, "quantityInterpretation": "six corridor control occurrences plus one elevator-lobby control occurrence" }, { "number": 3, "text": "FAN WILL RUN CONTINUOUSLY AS THE NOTE ON EXHAUST FAN SCHEDULES (M1.1).", "planMarkerCount": 1, "quantityInterpretation": "one reference at EF-1.1" } ] }, "rooms": { "guestroomCount": 24, "supportOrCirculationCount": 5, "plottedRoomLabels": [ { "number": "401", "name": "KING STUDIO" }, { "number": "403", "name": "KING STUDIO" }, { "number": "405", "name": "KING STUDIO CONNECTING" }, { "number": "407", "name": "ACCESSIBLE KING ONE BEDROOM" }, { "number": "409", "name": "KING STUDIO" }, { "number": "411", "name": "KING STUDIO" }, { "number": "413", "name": "KING STUDIO" }, { "number": "415", "name": "KING STUDIO" }, { "number": "417", "name": "KING STUDIO" }, { "number": "419", "name": "KING STUDIO" }, { "number": "421", "name": "KING STUDIO" }, { "number": "423", "name": "STORAGE" }, { "number": "400", "name": "ELEVATOR LOBBY" }, { "number": "001", "name": "STAIR 1" }, { "number": "433", "name": "CORRIDOR" }, { "number": "002", "name": "STAIR 2" }, { "number": "402", "name": "KING ONE BEDROOM" }, { "number": "404", "name": "KING STUDIO" }, { "number": "406", "name": "KING STUDIO" }, { "number": "408", "name": "KING STUDIO" }, { "number": "410", "name": "KING STUDIO" }, { "number": "412", "name": "KING STUDIO" }, { "number": "414", "name": "KING STUDIO" }, { "number": "416", "name": "QUEEN QUEEN" }, { "number": "418", "name": "QUEEN QUEEN" }, { "number": "420", "name": "QUEEN QUEEN" }, { "number": "422", "name": "QUEEN QUEEN" }, { "number": "424", "name": "QUEEN QUEEN CONNECTING" }, { "number": "426", "name": "KING ACCESSIBLE" } ], "guestroomNumbers": [ "401", "402", "403", "404", "405", "406", "407", "408", "409", "410", "411", "412", "413", "414", "415", "416", "417", "418", "419", "420", "421", "422", "424", "426" ], "evidence": "Twenty-four numbered guestrooms are plotted. Storage 423, Elevator Lobby 400, Corridor 433, Stair 1/001 and Stair 2/002 are separately labeled.", "typicalRoomTreatment": "General note 9 sends guestroom lighting layouts to E4.0/E4.1. Guestroom furniture/background outlines and room labels are not installed lighting occurrences on E2.3 and are not counted here." }, "gridAndPlanEvidence": { "horizontalGridLabels": [ "1", "2", "3", "4", "5", "6", "7", "8", "9", "10", "11", "12", "13", "14", "15" ], "verticalGridLabels": [ "A", "B", "C", "D", "E", "F", "G", "H", "J", "J.1", "J.2" ], "planDetail": { "number": "1", "title": "LIGHTING FOURTH FLOOR PLAN", "scale": "1/8 inch = 1 foot" } }, "references": [ { "source": "General note 5", "reference": "NEC 700.12(F)", "subject": "emergency/exit lights ahead of local switches" }, { "source": "General note 6", "reference": "NFPA 101 Sections 7.8.1.3 and 7.9", "subject": "emergency illumination" }, { "source": "General notes 7 and 11", "reference": "IBC Sections 1013.1 and 1013.5 / Section 1013", "subject": "low-level and furnished exit signs" }, { "source": "General note 9", "reference": "E4.0, E4.1", "subject": "typical guestroom lighting plans" }, { "source": "General note 12", "reference": "NFPA 13", "subject": "fixture/sprinkler coordination" }, { "source": "Keyed note 1", "reference": "L1.B-33; NEC 700.12(I)(2)(3)", "subject": "stair S02/X1/X2, 2#10, 1/2 inch conduit, lock-on" }, { "source": "Keyed note 2", "reference": "C405.2.1.4", "subject": "corridor occupant-sensor reduction to no more than 50 percent within 20 minutes" }, { "source": "Keyed note 3", "reference": "M1.1", "subject": "continuous exhaust-fan operation" } ], "checks": [ { "id": "C01", "test": "count-marker reconciliation", "result": "pass", "detail": { "EF-1": 1, "S02": 4, "EM": 11, "R11": 21, "OS": 7, "S01": 1, "X3": 5, "X1": 3, "PA-204": 25, "EF-1.1": 1, "X2": 2, "HOME-RUN": 1 } }, { "id": "C02", "test": "R11 breakdown", "result": "pass", "detail": "17 corridor + 4 elevator lobby = 21" }, { "id": "C03", "test": "S02 breakdown", "result": "pass", "detail": "2 Stair 2 + 2 Stair 1 = 4" }, { "id": "C04", "test": "EM breakdown", "result": "pass", "detail": "6 corridor + 2 Stair 2 + 2 Stair 1 + 1 Storage = 11" }, { "id": "C05", "test": "wire run arithmetic", "result": "pass", "detail": "64 source curves; 395.616 raw LF; 395.5 LF aggregate rounded to nearest 0.5" }, { "id": "C06", "test": "guestroom double-count protection", "result": "pass", "detail": "24 room labels retained; no furniture/typical-room symbol counted as an E2.3 installed fixture" }, { "id": "C07", "test": "scale resolution relation", "result": "pass", "detail": "10800/2592 = 7200/1728 = 4.1666667 raster pixels/PDF point; 9 PDF points/ft = 37.5 raster pixels/ft" } ], "issues": [ { "number": 1, "severity": "coordination", "title": "Guestroom takeoff is cross-sheet only", "text": "E2.3 plots room/background geometry but general note 9 directs detailed guestroom lighting to E4.0/E4.1. Do not multiply or count typical-room symbols as E2.3 plotted occurrences without a separate room-type mapping." }, { "number": 2, "severity": "open", "title": "Dual circuit allocation not graphically separated", "text": "The connected corridor/lobby network has one L1.B-25,27 home-run callout. The drawing does not assign each traced segment to circuit 25 versus 27, so conductor count and installed conductor LF are not certified." }, { "number": 3, "severity": "open", "title": "Stair circuit route not drawn", "text": "Keyed note 1 specifies L1.B-33, 2#10 and 1/2-inch conduit for S02, X1 and X2 at staircases, but no panel-to-device route is visibly plotted. No LF is inferred." }, { "number": 4, "severity": "ambiguity", "title": "Keynote-1 bubble scope exceeds note wording", "text": "Keynote 1 bubbles appear adjacent to stair emergency units as well as S02 fixtures, while the keyed-note text explicitly names only S02, X1 and X2. Confirm whether EM units are intended on L1.B-33." }, { "number": 5, "severity": "cross_sheet", "title": "Exhaust-fan schedule reference requires validation", "text": "Keyed note 3 cites exhaust-fan schedules on M1.1 for EF-1.1. Confirm that M1.1 contains the governing schedule/continuous-operation note; no fan branch circuit or disconnect detail is added here." }, { "number": 6, "severity": "coordination", "title": "Sensor behavior uses two timing criteria", "text": "General note 4 requires occupancy-sensor lighting off within 30 minutes; keyed note 2 requires corridor reduction to no more than 50 percent within 20 minutes. These may be staged behaviors, but sequence/control intent must be coordinated." }, { "number": 7, "severity": "field_verification", "title": "Emergency illumination can require additions", "text": "General note 13 states field inspection will determine sufficiency and may require additional emergency lighting. Count 11 is the plotted count only." }, { "number": 8, "severity": "source_limit", "title": "No independent scale dimension", "text": "The printed 1/8-inch scale is internally verified against PDF/raster resolution, but the plan field has no legible independent dimension chain suitable for a second calibration." }, { "number": 9, "severity": "source_limit", "title": "Fixture identities depend on E2.0 schedule", "text": "E2.3 has no luminaire schedule. PA-204, R11, S01, S02, X1, X2 and X3 descriptions are reconciled from the established E2.0 schedule/legend; E2.3 plotted tag counts remain independently counted." }, { "number": 10, "severity": "provenance", "title": "OCR omission", "text": "source-40.txt omits most plotted tags and note bodies. Certification therefore relies on the full-resolution raster and underlying vector geometry, with unreadable items left uninferred." } ], "certification": { "scope": "actual plotted occurrences and visible drawn connection paths on E2.3 only", "excluded": "unshown installation routing, drops, conductor LF, typical guestroom fixtures and source-obscured quantities", "countTotalAllMarkerCategories": 82, "fixtureAndDeviceTotalExcludingHomeRun": 81, "statement": "Counts are one marker per visible plotted occurrence. Reference bubbles and repeated note text are not installed quantities." }, "independentCrossCheck": { "audit": { "name": "Independent cross-sheet reconciliation - E1.2 and E2.1-E2.4", "mode": "read-only, fail-closed", "overallStatus": "HOLD", "sourceDirectory": "/workspace/sites/ssx-cover-release/tmp/pdfs/next5-e12-e23/", "sources": [ { "sheet": "E1.2", "pdfPage": 36, "image": "source-36.png", "role": "lighting fixture schedule" }, { "sheet": "E2.1", "pdfPage": 38, "image": "source-38.png", "role": "second-floor lighting plan" }, { "sheet": "E2.2", "pdfPage": 39, "image": "source-39.png", "role": "third-floor lighting plan" }, { "sheet": "E2.3", "pdfPage": 40, "image": "source-40.png", "role": "fourth-floor lighting plan" }, { "sheet": "E2.4", "pdfPage": 41, "image": "source-41.png", "role": "fifth-floor lighting plan" } ], "priorEvidence": [ "/workspace/sites/ssx-cover-release/dist/e11-full-audit.json", "/workspace/sites/ssx-cover-release/dist/takeoff-data.json", "/workspace/sites/ssx-cover-release/dist/fixture-marks.json", "/workspace/sites/ssx-cover-release/dist/wire-takeoff.json" ], "scopeLimits": [ "Only visible, legible plan and schedule evidence was used; no symbol count was inferred from a schedule row or note bubble.", "E2.1-E2.4 do not plot the complete in-room guestroom lighting layouts; general note 9 directs those layouts to E4.0 and E4.1.", "No installed wire or conduit length is released from diagrammatic circuit arcs, and no E2.0 length is multiplied across repeated floors.", "Presence of referenced destination sheets is distinguished from technical verification of those destinations." ] }, "summary": { "overallStatus": "HOLD", "passFindings": 10, "holdFindings": 9, "releaseReason": "The four-floor room/circuit pattern reconciles, but E2.4 contains an S04 fixture tag with no E1.2 schedule definition; complete fixture totals, occupancy-control quantities, branch routing, panel-schedule confirmation, wall-fixture heights, and final emergency/exit adequacy also remain unresolved by this batch." }, "scheduleCoverage": { "scheduledTypeCount": 33, "sections": [ { "name": "Exterior lighting", "tags": [ "SA", "SA1", "SB", "SB1", "SC1", "S03", "S22", "G01", "R02" ] }, { "name": "General lighting", "tags": [ "R01", "R05", "R06", "R10", "R11", "S20", "T01", "T02", "S01", "S02", "TR10", "001" ] }, { "name": "Guestroom lighting", "tags": [ "GR10", "S21", "GR-203" ] }, { "name": "Decorative lighting", "tags": [ "PA-201", "PA-202", "PA-204", "PA-205" ] }, { "name": "Exit signs and emergency lighting", "tags": [ "X1", "X2", "X3", "EM", "EM1" ] } ], "visibleUpperFloorFixtureTags": [ "R11", "PA-204", "S02", "S04", "X1", "X2", "X3", "EM" ], "coverageConclusion": "R11, PA-204, S02, X1, X2, X3, and EM have E1.2 schedule rows. The single S04 fixture visibly plotted in Storage 523 on E2.4 has no E1.2 schedule definition and is an unresolved orphan tag.", "nonLightingTag": { "tag": "EF-1.1", "appearance": "One legible exhaust-fan reference near the storage/elevator area on each of E2.1-E2.4.", "treatment": "Four visible plan references, not lighting fixtures. Reconcile in the mechanical/equipment takeoff and do not add them to E1.2 fixture totals. Keyed note 3 sends operation to the M1.1 exhaust-fan schedule." } }, "floorReconciliation": { "upperFloorRoomCount": 96, "projectRoomCountWhenAddedToEstablishedE2_0": 107, "floors": [ { "sheet": "E2.1", "floor": 2, "guestrooms": 24, "corridor": "228", "circuitCallout": "L1.B-17,19", "stairCircuit": "L1.B-33", "distinctRoomCondition": "Room 226 is QUEEN QUEEN ACCESSIBLE; one connecting king studio at 205." }, { "sheet": "E2.2", "floor": 3, "guestrooms": 24, "corridor": "333", "circuitCallout": "L1.B-21,23", "stairCircuit": "L1.B-33", "distinctRoomCondition": "Room 326 is KING ACCESSIBLE; one connecting king studio at 305." }, { "sheet": "E2.3", "floor": 4, "guestrooms": 24, "corridor": "433", "circuitCallout": "L1.B-25,27", "stairCircuit": "L1.B-33", "distinctRoomCondition": "Room 426 is KING ACCESSIBLE; one connecting king studio at 405." }, { "sheet": "E2.4", "floor": 5, "guestrooms": 24, "corridor": "533", "circuitCallout": "L1.B-29,31", "stairCircuit": "L1.B-33", "distinctRoomCondition": "Room 526 is KING ACCESSIBLE; connecting king studios occur at 505, 512, and 514." } ], "repeatedGraphicFinding": "The corridor, elevator-lobby, stair, common-fixture, exit/emergency, and control topology is visually repeated on all four sheets. The sheets are not interchangeable quantity sources because room types/numbers and circuit-pair callouts differ.", "establishedFirstFloorGuestroomEvidence": { "rooms": 11, "fixtureSubtotal": 72, "breakdown": { "GR10": 37, "S21": 24, "GR-203": 11 }, "restriction": "The 72-fixture subtotal is mapped only to the eleven E2.0 guestrooms. It cannot be averaged or multiplied by 96 because upper-floor room types and two-room suites differ and E2.1-E2.4 defer in-room layouts to E4.0/E4.1." } }, "findings": [ { "id": "PASS-01", "status": "PASS", "topic": "E1.1 to E1.2 reference chain", "sheets": [ "E1.1", "E1.2" ], "evidence": [ "E1.1 note 7 explicitly names the lighting fixture schedule on E1.2.", "E1.2 is the lighting fixture schedule and contains 33 named type rows across exterior, general, guestroom, decorative, and exit/emergency sections." ], "conclusion": "The destination sheet identity is correct." }, { "id": "PASS-02", "status": "PASS", "topic": "Covered upper-floor fixture tags excluding S04", "sheets": [ "E1.2", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "Visible upper-floor plan lighting tags with schedule coverage are R11, PA-204, S02, X1, X2, X3, and EM.", "Each has a distinct E1.2 schedule row." ], "conclusion": "These seven tags reconcile to E1.2; S04 is excluded from this pass and separately held as a broken schedule chain." }, { "id": "PASS-03", "status": "PASS", "topic": "Room-count chain", "sheets": [ "E2.0", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "Each of E2.1-E2.4 contains 24 numbered guestrooms, for 96 upper-floor rooms.", "The established E2.0 guestroom register contains 11 first-floor rooms.", "96 + 11 = 107." ], "conclusion": "The five lighting-plan room count reconciles to 107 guestrooms." }, { "id": "PASS-04", "status": "PASS", "topic": "Repeated-floor circuit progression", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "The main common-lighting callouts progress without duplication: L1.B-17,19; L1.B-21,23; L1.B-25,27; and L1.B-29,31.", "All four sheets separately repeat staircase circuit L1.B-33 under keyed note 1." ], "conclusion": "The floor-specific circuit pairs are distinct, while the common stair circuit is intentionally repeated." }, { "id": "PASS-05", "status": "PASS", "topic": "Emergency fixture duration", "sheets": [ "E1.2", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "E1.2 marks X1, X2, X3, EM, and EM1 for 90-minute emergency operation.", "E2.1-E2.4 general note 4 requires all emergency lighting to maintain at least 90 minutes of operation upon power failure." ], "conclusion": "The schedule and plan notes agree on 90-minute operation." }, { "id": "PASS-06", "status": "PASS", "topic": "Stair emergency/control assembly treatment", "sheets": [ "E1.2", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "E1.2 S02 is a stairwell strip light with integral occupancy sensor, bi-level dimming, and emergency designation.", "Keyed note 1 connects S02, X1, and X2 at staircases to L1.B-33 using 2 #10 conductors in 1/2-inch conduit and requires a lock-on feature." ], "conclusion": "The S02 emergency and sensor features are part of the scheduled S02 assembly, not separate fixtures." }, { "id": "PASS-07", "status": "PASS", "topic": "Circuit-before-switch requirement", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "General note 5 requires emergency and exit lights connected to local normal circuits to connect ahead of local switches." ], "conclusion": "The four upper-floor sheets carry a consistent unswitched emergency/exit requirement." }, { "id": "PASS-08", "status": "PASS", "topic": "Guestroom detail destinations", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4", "E4.0", "E4.1" ], "evidence": [ "General note 9 on each upper-floor plan directs detailed guestroom layouts to E4.0 and E4.1.", "The drawing-package register identifies both E4.0 and E4.1 as existing sheets." ], "conclusion": "The destination sheet numbers exist; technical quantity reconciliation remains separately held." }, { "id": "PASS-09", "status": "PASS", "topic": "Exhaust fan reference destination", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4", "M1.1" ], "evidence": [ "Each upper-floor plan visibly references EF-1.1 near the storage/elevator area.", "Keyed note 3 states the fan will run continuously as noted on the exhaust-fan schedules on M1.1.", "M1.1 contains an EF-1.1 schedule row for ice-machine/mop-sink service at 100 CFM." ], "conclusion": "The mechanical schedule destination exists and the four electrical-plan references are not lighting fixtures." }, { "id": "PASS-10", "status": "PASS", "topic": "Printed scale equivalence", "sheets": [ "E2.0", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "Each upper-floor plan prints 1/8 inch = 1 foot.", "The established E2.0 vector method uses 9 PDF points per foot, equal to 72 points/inch times 1/8 inch/foot.", "At the 300-dpi source render, the equivalent raster factor is 37.5 pixels per foot." ], "conclusion": "The mathematical scale conversion is consistent across the lighting plans.", "qualification": "No independent written-dimension calibration was found on these sheets." }, { "id": "HOLD-01", "status": "HOLD", "topic": "Complete upper-floor fixture totals", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4", "E4.0", "E4.1" ], "evidence": [ "The four upper-floor plans show common-area lighting but do not plot complete in-room guestroom fixtures.", "General note 9 explicitly sends detailed room layouts to E4.0 and E4.1.", "The established E2.0 total of 72 guestroom fixtures applies only to eleven mapped first-floor rooms and has nonuniform tag counts." ], "conclusion": "A complete fixture total for the 96 upper-floor guestrooms cannot be certified from this batch.", "requiredResolution": "Apply the audited E4.0/E4.1 type-level fixture assemblies to a verified room-type matrix, preserving one-bedroom and accessible variants." }, { "id": "HOLD-02", "status": "HOLD", "topic": "Common-area fixture occurrence totals", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "The four sheets visually repeat the same common-area fixture topology, but no prior symbol register or marked-count evidence was supplied for E2.1-E2.4.", "The E1.2 schedule contains type definitions and no quantity column." ], "conclusion": "Do not release or multiply common-area fixture quantities until each sheet receives a symbol-by-symbol occurrence trace.", "requiredResolution": "Create per-sheet occurrence registers for R11, PA-204, S02, X1, X2, X3, and EM and reconcile repeated coordinates without treating one floor as a four-floor multiplier." }, { "id": "HOLD-03", "status": "HOLD", "topic": "Occupancy sensor location and quantity", "sheets": [ "E1.1", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "Keyed note 2 requires corridor lighting to reduce to no more than 50 percent within 20 minutes after vacancy.", "The same note directs verification of sensor detection range, locations, and quantities with the supplier/manufacturer.", "E1.1 note 2 defines Wattstopper CX-105 with A120E-P power pack but establishes no installed quantity." ], "conclusion": "The performance rule is defined, but final sensor and power-pack quantities are not construction-release ready.", "requiredResolution": "Obtain the lighting-controls shop drawing and reconcile every plan control marker to sensor and power-pack hardware." }, { "id": "HOLD-04", "status": "HOLD", "topic": "Upper-floor circuit/panel schedule confirmation", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4", "E6.1" ], "evidence": [ "Upper-floor common-lighting callouts use L1.B circuit pairs 17/19, 21/23, 25/27, and 29/31.", "Stair fixtures on all four sheets use L1.B-33.", "The supplied established E2.0 data confirms an E6.1 reference for L1.B-33 but does not establish the four upper-floor circuit-pair schedule rows." ], "conclusion": "The plan callouts are legible and nonduplicative, but breaker/description/conductor agreement for circuits 17-31 is not certified here.", "requiredResolution": "Verify L1.B circuits 17, 19, 21, 23, 25, 27, 29, and 31 against the governing panel schedule and connected loads." }, { "id": "HOLD-05", "status": "HOLD", "topic": "Wiring path and installed LF", "sheets": [ "E2.0", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "The established E2.0 methodology measures 1,819.102 LF of drawn connection paths and only 254.730 LF of conductor where conductor allocation is explicitly known.", "It excludes panel-to-home-run routing, vertical rises/drops, grounds, switched and unswitched leg allocation, controls, slack, terminations, and waste.", "Upper-floor curved connection lines are diagrammatic and do not establish ceiling pathway elevation or complete panel routes." ], "conclusion": "Neither E2.0 LF nor geometric repetition may be multiplied by four as installed upper-floor wire/conduit.", "requiredResolution": "Trace each sheet's drawn centerlines separately if drawing LF is needed, then obtain routed pathways and conductor allocations before converting to installed quantities." }, { "id": "HOLD-06", "status": "HOLD", "topic": "Mounting-height reference is incomplete", "sheets": [ "E1.1", "E1.2", "E7.0" ], "evidence": [ "E1.1 note 7 refers to E1.2 and detail 1/E7.0 for fixture mounting height.", "E1.2 provides mounting categories such as wall, ceiling, recessed, pendant, pole, track, and surface, but does not provide a numeric mounting height for each wall-mounted fixture.", "E1.2 note 5 requires wall-mounted fixture heights to be verified with the owner/architect before installation." ], "conclusion": "E1.2 alone does not close the mounting-height chain.", "requiredResolution": "Coordinate type-specific heights with 1/E7.0 and owner/architect approval; issue written clarification where no numeric height is provided." }, { "id": "HOLD-07", "status": "HOLD", "topic": "Emergency and low-level exit adequacy", "sheets": [ "E1.2", "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "General notes require emergency illumination levels, low-level exit signs in guestroom-serving Group R-1 areas, and contractor verification of IBC Section 1013 compliance.", "The notes state that final emergency-lighting adequacy is determined during on-site inspection and additional units may be required." ], "conclusion": "Visible X1/X2/X3/EM marks are plan occurrences, but final code-required quantity is explicitly open.", "requiredResolution": "Complete photometric/egress review and track inspector-required additions separately from drawn counts." }, { "id": "HOLD-08", "status": "HOLD", "topic": "Independent scale validation", "sheets": [ "E2.1", "E2.2", "E2.3", "E2.4" ], "evidence": [ "The plans print 1/8 inch = 1 foot, supporting 9 PDF points/ft or 37.5 render pixels/ft.", "No two legible written plan dimensions were found on these sheets to independently validate the plotted scale." ], "conclusion": "The printed conversion is usable for provisional drawn-line measurement but remains unverified for certified quantity release.", "requiredResolution": "Validate against two independent written dimensions or a calibrated source before accepting measured LF." }, { "id": "HOLD-09", "status": "HOLD", "topic": "Missing S04 fixture schedule definition", "sheets": [ "E1.2", "E2.4" ], "evidence": [ "E2.4 visibly plots one fixture tagged S04 in Storage 523.", "E1.2 contains no S04 row; its scheduled S-tags are S01, S02, S03, S20, S21, and S22." ], "conclusion": "The E2.4 S04 occurrence has no fixture description, manufacturer/catalog basis, mounting, wattage, lumen output, color temperature, voltage, dimming, finish, emergency attribute, or notes in the governing fixture schedule.", "quantityTreatment": "Retain one visible unresolved S04 plan occurrence on E2.4. Do not substitute another S-tag, omit it, or add a schedule-row quantity by inference.", "requiredResolution": "Issue a coordinated E1.2 S04 schedule row or correct the E2.4 tag in writing, then reconcile its controls, circuiting, and emergency attributes." } ], "duplicateAndQuantityRules": [ { "source": "E1.2 schedule rows and symbols", "rule": "Type definitions only; scheduledTypeCount 33 is not an installed fixture count." }, { "source": "E2.4 S04 in Storage 523", "rule": "One visible installed-plan occurrence with no E1.2 type definition. Carry as unresolved S04; do not map it to S01, S02, S03, S20, S21, or S22 by similarity." }, { "source": "E2.1-E2.4 repeated floor graphics", "rule": "Count each physical floor occurrence once. Do not count one floor and apply a four-floor multiplier without confirming floor-specific room and circuit differences." }, { "source": "Keyed-note bubbles 1, 2, and 3", "rule": "Reference markers only; do not count them as fixtures, sensors, lock-on devices, or fans." }, { "source": "EM followed by keyed-note bubble 1", "rule": "Treat as an EM fixture plus a note-1 reference, not fixture type EM1. EM1 is a separate scheduled exterior wallpack type." }, { "source": "S02", "rule": "Integral sensor, bi-level dimming, and emergency attributes belong to the scheduled strip-light assembly; do not add separate fixture units for those attributes." }, { "source": "PA-205", "rule": "One plan symbol is one three-light pendant assembly, not three assemblies." }, { "source": "TR10", "rule": "Track heads, track arrangements, track LF, feeds, and fittings are separate measures. Established E2.0 evidence has 41 heads on seven arrangements but unresolved track LF/fittings." }, { "source": "G01", "rule": "One schedule row is not one lamp or one foot. Established E2.0 evidence has 58.382 drawing LF; lamp spacing, sag/supports, and installed length remain open." }, { "source": "EF-1.1", "rule": "A mechanical exhaust-fan plan occurrence/reference, not an E1.2 lighting fixture." }, { "source": "L1.B-33", "rule": "The same common stair circuit is referenced on four floor sheets; do not create four panel circuits numbered 33. Count physical branch segments only from an explicit routed basis." }, { "source": "E2.0 first-floor guestroom subtotal", "rule": "Do not average or multiply 72 fixtures across upper-floor rooms; reconcile GR10, S21, and GR-203 by verified typical-room type." }, { "source": "E1.2 EM column", "rule": "An x in the EM column is an attribute of that fixture type, not an extra emergency fixture." } ], "releaseChecks": [ { "status": "PASS", "check": "R11, PA-204, S02, X1, X2, X3, and EM are covered by E1.2." }, { "status": "PASS", "check": "Each upper floor has 24 guestrooms; 96 upper plus 11 first floor equals 107." }, { "status": "PASS", "check": "Floor circuit pairs are distinct: 17/19, 21/23, 25/27, 29/31." }, { "status": "PASS", "check": "E1.2 and upper-floor notes agree on 90-minute emergency operation." }, { "status": "PASS", "check": "E4.0, E4.1, M1.1, and E7.0 destination sheets exist in the drawing package." }, { "status": "HOLD", "check": "Complete upper-floor in-room fixture quantities require E4.0/E4.1 type reconciliation." }, { "status": "HOLD", "check": "Common-area fixtures require per-sheet marked occurrence registers before quantity release." }, { "status": "HOLD", "check": "Occupancy sensor and power-pack quantities require controls shop-drawing reconciliation." }, { "status": "HOLD", "check": "Verify L1.B circuits 17-31 against the governing panel schedule." }, { "status": "HOLD", "check": "Installed wire/conduit LF is not established by diagrammatic arcs or repeated geometry." }, { "status": "HOLD", "check": "Wall-mounted fixture heights require 1/E7.0 and owner/architect coordination." }, { "status": "HOLD", "check": "Final emergency/exit adequacy and field-added units remain open." }, { "status": "HOLD", "check": "Printed scale lacks independent written-dimension calibration." }, { "status": "HOLD", "check": "E2.4 Storage 523 S04 has no E1.2 schedule definition." } ] } } }, "issues": [ { "id": "E23-01", "title": "Guestroom Takeoff Is Cross-Sheet Only", "text": "E2.3 plots room/background geometry but general note 9 directs detailed guestroom lighting to E4.0/E4.1. Do not multiply or count typical-room symbols as E2.3 plotted occurrences without a separate room-type mapping." }, { "id": "E23-02", "title": "Dual Circuit Allocation Not Graphically Separated", "text": "The connected corridor/lobby network has one L1.B-25,27 home-run callout. The drawing does not assign each traced segment to circuit 25 versus 27, so conductor count and installed conductor LF are not certified." }, { "id": "E23-03", "title": "Stair Circuit Route Not Drawn", "text": "Keyed note 1 specifies L1.B-33, 2#10 and 1/2-inch conduit for S02, X1 and X2 at staircases, but no panel-to-device route is visibly plotted. No LF is inferred." }, { "id": "E23-04", "title": "Keynote-1 Bubble Scope Exceeds Note Wording", "text": "Keynote 1 bubbles appear adjacent to stair emergency units as well as S02 fixtures, while the keyed-note text explicitly names only S02, X1 and X2. Confirm whether EM units are intended on L1.B-33." }, { "id": "E23-05", "title": "Exhaust-Fan Schedule Reference Requires Validation", "text": "Keyed note 3 cites exhaust-fan schedules on M1.1 for EF-1.1. Confirm that M1.1 contains the governing schedule/continuous-operation note; no fan branch circuit or disconnect detail is added here." }, { "id": "E23-06", "title": "Sensor Behavior Uses Two Timing Criteria", "text": "General note 4 requires occupancy-sensor lighting off within 30 minutes; keyed note 2 requires corridor reduction to no more than 50 percent within 20 minutes. These may be staged behaviors, but sequence/control intent must be coordinated." }, { "id": "E23-07", "title": "Emergency Illumination Can Require Additions", "text": "General note 13 states field inspection will determine sufficiency and may require additional emergency lighting. Count 11 is the plotted count only." }, { "id": "E23-08", "title": "No Independent Scale Dimension", "text": "The printed 1/8-inch scale is internally verified against PDF/raster resolution, but the plan field has no legible independent dimension chain suitable for a second calibration." }, { "id": "E23-09", "title": "Fixture Identities Depend On E2.0 Schedule", "text": "E2.3 has no luminaire schedule. PA-204, R11, S01, S02, X1, X2 and X3 descriptions are reconciled from the established E2.0 schedule/legend; E2.3 plotted tag counts remain independently counted." }, { "id": "E23-10", "title": "Ocr Omission", "text": "source-40.txt omits most plotted tags and note bodies. Certification therefore relies on the full-resolution raster and underlying vector geometry, with unreadable items left uninferred." } ] }